Silex technology SX-550 manual Access Http Pages, ExtendView Configuration Window

Page 33

7. Select Configuration. The Server Configuration window displays as shown in Figure 14.

Figure 14 ExtendView Configuration Window

8.If no DHCP server exists, Extendview will prompt for a password before the configuration page displays. If you are unsure of the IP address, check with your network administrator.

9.If using a wireless SX-550 module, configure the wireless settings by selecting country or region for the region of operation.

NOTE: It may not be legal to operate the SX-550 module in a country or region other than the country or region shown in the drop-down list. If your country or region is not listed, please check with your local government agency.

Set the wireless mode as ad-hoc or infrastructure, SSID channel, and WEP encryption of the wireless SX-550 module to the same configuration as the wireless network where you are communication. All nodes must have the identical same settings to communicate with each other.

10.Continue to Chapter 6:

Setting Configuration Parameters.

Access HTTP Pages

You can manage and configure the SX-550 module using a standard web browser, such as Internet Explorer or Mozilla Firefox.

NOTE: Prior to accessing the SX-550 module, you must configure the IP on both the computer and SX- 550 module.

To access the HTTP Pages:

1.Connect an Ethernet cable from your network hub to the SX-550 module.

2.Power on the computer and SX-550 module.

If the SX-550 module is connected to a serial device that cannot display or print ASCII characters, then it is recommended that another serial device capable of displaying or printing ASCII characters be temporarily connected to the SX-550 module. This ensures you can view the IP address assigned by the DHCP server to the SX-550 module. The IP address must be different than the IP address used by the computer.

Accessing Configuration Parameters

silex

Page 27

 

Part Number 40183-101

 

Image 33
Contents Developer’s Reference Guide Trademarks Contents Configuring Serial Port Monitor Alert and Trap Configuration Figures Silex Contents Part Number Safety Precautions About This Reference GuideEmissions Disclaimer Silex About This Reference Guide Part Number Introduction Processor and Wireless LAN Radio PCBSilex Introduction Part Number Chapter Getting Started Installing Wlan Module in DaughtercardVerify Development Kit Contents Wlan Module Inserted in Daughtercard Installing the SX-550 Wlan ModuleSX-550 Evaluation Daughtercard Status Monitors Function State Monitoring Module StatusOEM Interface Pinout Signal OEM InterfaceFunction State Status OEM Interface Signal Description Pin Type Power Input Electrical CharacteristicsPower Management Serial Peripheral InterfaceSerial Ports Logical Serial Port Signal Descriptions Pin Input/OutputGround General Purpose IO General Purpose IO Signal Descriptions Pin SelectableEvaluation CN210 Drive High/Low Description Daughtercard LEDs and General Purpose IO SignalsLED and Gpio Descriptions GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7RS-232 Cable Additional OEM Interface SignalsUART0TXD, UART0RTS UART1TXD, UART1RTS OEM Interface Electrical CharacteristicsChapter Using the SX-550 Wlan Module Using the Wireless MethodEvaluation Module Connections Access silex Console Interface Using the Wired Ethernet MethodPort Settings Parameter Generating Configuration Data Pushbutton FunctionsAction Result Silex Using the SX-550 Wlan Module Part Number Access ExtendView Utility Chapter Accessing Configuration ParametersInstalling ExtendView Utility ExtendView Main Using ExtendView UtilityCreate View with Default Settings ExtendView Configuration Window Access Http PagesSX-550 Home Access Internal Command ConsoleUsing Telnet Session Using Terminal Emulator through the Serial PortTelnet Where x.x.x.x is the IP address of the SX-550 module Standard AT Commands Supported Using AT Modem CommandsAT Commands Parameter Description Extended AT Commands Parameter Description Parameter Command DescriptionResponse Codes AT#Cset nw ssid silex#CsaveFactory Default Settings Chapter Setting Configuration ParametersFactory Default Settings Parameter Description CTS/RTSRestoring Factory Default Settings Modify Basic SettingsChanging Serial Settings Parameter Description Settings Default SettingParameter Setting Serial Setting ParametersTCP/IP Window Modifying TCP/IP SettingsChange Password Window TCP/IP SettingsDNS TCP/IP Configuration Settings ParameterConfigure Simple Network Management Protocol Snmp CommandsCommand Description Snmp Trap Settings Parameter Configuring Gpio Alerts and TrapsGpio Commands Description Show Gpio DIRSET Gpio DIR in OUT Gpio # Gpio Trigger Commands Description Show Gpio SpecialSET Gpio Special ENA/DIS Gpio Transmit Commands Description Trig # Email String Gpio #1 is Gpio #2 isTrig # Email String Your email text msg here Gpio #2 is Port Monitor Alert Commands Description Show Port S1 TrigmonIndex # Monitor String Show Port S1 Trigxmt Trigmon Commands DescriptionIndex # Xmit String Index # Xmit String Trigger string was seenOEM Header Interface Pinout Signal Designing with the SX-550OEM Header Interface Differential Output Ethernet Transmit Data primary Antenna Connectors Ethernet PHY Transformer Specification10/100M Magnetics Manufacturers Part Number General Purpose I/O InterfaceYCL GTS40-Pin Drive High/Low Description PowerProduct Specifications Chapter Product SpecificationsComponent Specifications Radio Performance Specifications ParameterTKIP, AES Parameter SpecificationsReceiver Sensitivity Production Specification TCP Port Connections TCP Port ConnectionsPort Destination Device Wireless and Network Security Commands Appendix a Console CommandsNetwork Commands Description SET NW AUTHtype Open Shared Ttls Leap WPA-PSKSET NW KEY# SET NW ENCSET NW RTS Name User defined SET NW CertcnCommon name SET NW CERTCN2SET NW Certkey SET NW CertexpSET NW ID SET NW PWSET NW Wpagroup Enable Disable Port Commands Description Port CommandsXON/XOFF RS232 CL Port S1 JOBServer Information Commands Description Sample Output Server Information CommandsSET Port S1 Stop 1 SET Snmp GetcommSnmp is Enabled Command Description Sample OutputSerial server Firmware Ver .19 Boot Ver 16Mbit Flash SET Snmp LOCation stringService Commands Description Service CommandsSET Servi service name FRS SET Servi service name FRMSET Servi service name IP ENable DIsable SET Servi service name NAme NewnameString Commands Description String CommandsEnter LANGUAGE= POSTSCRIPT\0ATCP/IP Commands Description TCP/IP CommandsSET IP FTP Auto Bootp Rarp Dhcp StaticSET IP Http SET IP LPDSET IP Tftp SET IP TCPFirmware Update Power Configuration CommandsPower Configuration Command Description Firmware Update Command DescriptionFirmware load is disabled SET LOAd ENable DIsableSET LOAd HOst Name SET LOAd IP Aa.bb.cc.ddMiscellaneous Commands Help CommandsMiscellaneous Commands Appendix B Engineering Drawings Antenna Cable AssemblyElectrical Specifications for Antenna Vswr Electrical Specifications Parameter ValueSilex technology america, Inc