Silex technology manual Designing with the SX-550, OEM Header Interface

Page 52

Chapter 7: Designing with the SX-550

OEM Header Interface

Table 30 describes the OEM header interface pinout for the SX-550 WLAN Module. Table 31 describes the OEM interface signal descriptions. All input and output signals, except the differential signals, are 0 to 3.3 V logic signals.

Table 30 OEM Header Interface Pinout

Pin	Signal	Pin	Signal

1	TPRX+	2	TPTX+

3	TPRX-	4	TPTX-

5	GPIO_7	6	GPIO_8

7	AVDD	8	+3.3VDD

9	UART0_RXD	10	GPIO_9

11	UART0_TXD	12	GPIO_10

13	GND	14	+3.3VDC

15	UART0_RTS	16	UART0_CTS

17	UART1_RTS	18	UART1_CTS

19	GND	20	GND

21	UART1_TXD	22	UART1_RXD

23	GND	24	RESET_N

25	SPI_CS	26	SPI_CLK

27	+3.3VDC	28	GND

29	GPIO_1	30	SPI_SDO

31	GPIO_2	32	SPI_SDI

33	+3.3VDC	34	GND

35	GPIO_3	36	GPIO_4

37	GND	38	GND

39	GPIO_5	40	GPIO_6

silex	Page 46
Part Number 40183-101

Image 52

Contents Developer’s Reference Guide Trademarks Contents Configuring Serial Port Monitor Alert and Trap Configuration Figures Silex Contents Part Number About This Reference Guide Safety PrecautionsEmissions Disclaimer Silex About This Reference Guide Part Number Processor and Wireless LAN Radio PCB IntroductionSilex Introduction Part Number Installing Wlan Module in Daughtercard Chapter Getting StartedVerify Development Kit Contents Installing the SX-550 Wlan Module Wlan Module Inserted in DaughtercardSX-550 Evaluation Daughtercard Monitoring Module Status Status Monitors Function StateOEM Interface OEM Interface Pinout SignalFunction State Status OEM Interface Signal Description Pin Type Electrical Characteristics Power InputPower Management Serial Peripheral InterfaceLogical Serial Port Signal Descriptions Pin Input/Output Serial PortsGround General Purpose IO Signal Descriptions Pin Selectable General Purpose IOLEDs and General Purpose IO Signals Evaluation CN210 Drive High/Low Description DaughtercardLED and Gpio Descriptions GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7Additional OEM Interface Signals RS-232 CableOEM Interface Electrical Characteristics UART0TXD, UART0RTS UART1TXD, UART1RTSUsing the Wireless Method Chapter Using the SX-550 Wlan ModuleEvaluation Module Connections Using the Wired Ethernet Method Access silex Console InterfacePort Settings Parameter Pushbutton Functions Generating Configuration DataAction Result Silex Using the SX-550 Wlan Module Part Number Chapter Accessing Configuration Parameters Access ExtendView UtilityInstalling ExtendView Utility Using ExtendView Utility ExtendView MainCreate View with Default Settings Access Http Pages ExtendView Configuration WindowAccess Internal Command Console SX-550 HomeUsing Terminal Emulator through the Serial Port Using Telnet SessionTelnet Where x.x.x.x is the IP address of the SX-550 module Using AT Modem Commands Standard AT Commands SupportedAT Commands Parameter Description Parameter Command Description Extended AT Commands Parameter DescriptionResponse Codes AT#Cset nw ssid silex#CsaveChapter Setting Configuration Parameters Factory Default SettingsFactory Default Settings Parameter Description CTS/RTSModify Basic Settings Restoring Factory Default SettingsChanging Serial Settings Parameter Description Settings Default SettingSerial Setting Parameters Parameter SettingModifying TCP/IP Settings TCP/IP WindowTCP/IP Settings Change Password WindowTCP/IP Configuration Settings Parameter DNSSnmp Commands Configure Simple Network Management ProtocolCommand Description Configuring Gpio Alerts and Traps Snmp Trap Settings ParameterShow Gpio DIR Gpio Commands DescriptionSET Gpio DIR in OUT Gpio # Show Gpio Special Gpio Trigger Commands DescriptionSET Gpio Special ENA/DIS Trig # Email String Gpio #1 is Gpio #2 is Gpio Transmit Commands DescriptionTrig # Email String Your email text msg here Gpio #2 is Show Port S1 Trigmon Port Monitor Alert Commands DescriptionIndex # Monitor String Trigmon Commands Description Show Port S1 TrigxmtIndex # Xmit String Index # Xmit String Trigger string was seenDesigning with the SX-550 OEM Header Interface Pinout SignalOEM Header Interface Differential Output Ethernet Transmit Data primary Antenna Connectors Transformer Specification Ethernet PHYGeneral Purpose I/O Interface 10/100M Magnetics Manufacturers Part NumberYCL GTSPower 40-Pin Drive High/Low DescriptionChapter Product Specifications Product SpecificationsComponent Specifications Radio Performance Specifications ParameterParameter Specifications TKIP, AESReceiver Sensitivity Production Specification TCP Port Connections TCP Port ConnectionsPort Destination Device Appendix a Console Commands Wireless and Network Security CommandsNetwork Commands Description SET NW AUTHtype Open Shared Ttls Leap WPA-PSKSET NW ENC SET NW KEY#SET NW RTS SET NW Certcn Name User definedCommon name SET NW CERTCN2SET NW Certexp SET NW CertkeySET NW ID SET NW PWSET NW Wpagroup Enable Disable Port Commands Port Commands DescriptionXON/XOFF RS232 CL Port S1 JOBServer Information Commands Server Information Commands Description Sample OutputSET Port S1 Stop 1 SET Snmp GetcommCommand Description Sample Output Snmp is EnabledSerial server Firmware Ver .19 Boot Ver 16Mbit Flash SET Snmp LOCation stringService Commands Service Commands DescriptionSET Servi service name FRM SET Servi service name FRSSET Servi service name IP ENable DIsable SET Servi service name NAme NewnameString Commands String Commands DescriptionEnter LANGUAGE= POSTSCRIPT\0ATCP/IP Commands TCP/IP Commands DescriptionAuto Bootp Rarp Dhcp Static SET IP FTPSET IP Http SET IP LPDSET IP TCP SET IP TftpPower Configuration Commands Firmware UpdatePower Configuration Command Description Firmware Update Command DescriptionSET LOAd ENable DIsable Firmware load is disabledSET LOAd HOst Name SET LOAd IP Aa.bb.cc.ddHelp Commands Miscellaneous CommandsMiscellaneous Commands Antenna Cable Assembly Appendix B Engineering DrawingsElectrical Specifications for Antenna Electrical Specifications Parameter Value VswrSilex technology america, Inc