Silex technology SX-550 manual Miscellaneous Commands, Help Commands

Page 79

Miscellaneous Commands

 

 

Table 47 Miscellaneous Commands

 

 

 

 

Command

Description

 

 

SET DEFAULT

Set parameters to factory defaults

 

 

EXIT

This command exits the current configuration console session.

 

 

 

SH

FATal

Shows fatal error log, if fatal errors exist.

 

 

 

CL

FATal

Clears the fatal error log

 

 

INIT

Instructs the server to execute a soft reset when the next exit command is

 

 

executed.

 

 

SET PAssword

Sets the server access (read) password

 

 

SET POWERON

Sets Power on delay

 

 

SH POWERON

Displays Power on delay in seconds

 

 

SET PROTect

Sets update password to the string given.

 

 

CL PROTect

Sets update password to <null>.

 

 

SAVE

Saves the current configuration to non-volatile memory.

 

 

Without this command, the configuration is not saved unless an EXIT

 

 

command is performed.

 

 

SH TEst

Sends the configuration data via ASCII to the serial port

 

 

UNPROTECT

If an update password has been defined (SET PROTECT), this command

 

 

enters the password to allow configuration items to be modified.

 

 

After entering this command, the server will prompt for the update

 

 

password. If entered properly, the user will then be able to execute SET

 

 

commands to modify the server configuration. This lasts only until the

 

 

console session is terminated with an EXIT command.

 

 

 

Help Commands

For help, simply enter HELP preceding the command. The correct syntax and a brief description of the commands will display.

For example, when inquiring for various commands to display specific IP parameters, type HELP SHOW IP.or for commands to change specific wireless/network security parameters, type HELP SET NWRK.

Console Commands

silex

Page 73

 

Part Number 40183-101

 

Image 79
Contents Developer’s Reference Guide Trademarks Contents Configuring Serial Port Monitor Alert and Trap Configuration Figures Silex Contents Part Number About This Reference Guide Safety PrecautionsEmissions Disclaimer Silex About This Reference Guide Part Number Introduction Processor and Wireless LAN Radio PCBSilex Introduction Part Number Chapter Getting Started Installing Wlan Module in DaughtercardVerify Development Kit Contents Wlan Module Inserted in Daughtercard Installing the SX-550 Wlan ModuleSX-550 Evaluation Daughtercard Status Monitors Function State Monitoring Module StatusOEM Interface OEM Interface Pinout SignalFunction State Status OEM Interface Signal Description Pin Type Serial Peripheral Interface Electrical CharacteristicsPower Input Power ManagementSerial Ports Logical Serial Port Signal Descriptions Pin Input/OutputGround General Purpose IO General Purpose IO Signal Descriptions Pin SelectableGPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7 LEDs and General Purpose IO SignalsEvaluation CN210 Drive High/Low Description Daughtercard LED and Gpio DescriptionsRS-232 Cable Additional OEM Interface SignalsUART0TXD, UART0RTS UART1TXD, UART1RTS OEM Interface Electrical CharacteristicsUsing the Wireless Method Chapter Using the SX-550 Wlan ModuleEvaluation Module Connections Using the Wired Ethernet Method Access silex Console InterfacePort Settings Parameter Pushbutton Functions Generating Configuration DataAction Result Silex Using the SX-550 Wlan Module Part Number Access ExtendView Utility Chapter Accessing Configuration ParametersInstalling ExtendView Utility ExtendView Main Using ExtendView UtilityCreate View with Default Settings ExtendView Configuration Window Access Http PagesSX-550 Home Access Internal Command ConsoleUsing Terminal Emulator through the Serial Port Using Telnet SessionTelnet Where x.x.x.x is the IP address of the SX-550 module Standard AT Commands Supported Using AT Modem CommandsAT Commands Parameter Description AT#Cset nw ssid silex#Csave Parameter Command DescriptionExtended AT Commands Parameter Description Response CodesCTS/RTS Chapter Setting Configuration ParametersFactory Default Settings Factory Default Settings Parameter DescriptionParameter Description Settings Default Setting Modify Basic SettingsRestoring Factory Default Settings Changing Serial SettingsParameter Setting Serial Setting ParametersTCP/IP Window Modifying TCP/IP SettingsChange Password Window TCP/IP SettingsDNS TCP/IP Configuration Settings ParameterSnmp Commands Configure Simple Network Management ProtocolCommand Description Snmp Trap Settings Parameter Configuring Gpio Alerts and TrapsShow Gpio DIR Gpio Commands DescriptionSET Gpio DIR in OUT Gpio # Show Gpio Special Gpio Trigger Commands DescriptionSET Gpio Special ENA/DIS Trig # Email String Gpio #1 is Gpio #2 is Gpio Transmit Commands DescriptionTrig # Email String Your email text msg here Gpio #2 is Show Port S1 Trigmon Port Monitor Alert Commands DescriptionIndex # Monitor String Index # Xmit String Trigger string was seen Trigmon Commands DescriptionShow Port S1 Trigxmt Index # Xmit StringDesigning with the SX-550 OEM Header Interface Pinout SignalOEM Header Interface Differential Output Ethernet Transmit Data primary Antenna Connectors Ethernet PHY Transformer SpecificationGTS General Purpose I/O Interface10/100M Magnetics Manufacturers Part Number YCL40-Pin Drive High/Low Description PowerRadio Performance Specifications Parameter Chapter Product SpecificationsProduct Specifications Component SpecificationsTKIP, AES Parameter SpecificationsReceiver Sensitivity Production Specification TCP Port Connections TCP Port ConnectionsPort Destination Device SET NW AUTHtype Open Shared Ttls Leap WPA-PSK Appendix a Console CommandsWireless and Network Security Commands Network Commands DescriptionSET NW KEY# SET NW ENCSET NW RTS SET NW CERTCN2 SET NW CertcnName User defined Common nameSET NW PW SET NW CertexpSET NW Certkey SET NW IDSET NW Wpagroup Enable Disable CL Port S1 JOB Port CommandsPort Commands Description XON/XOFF RS232SET Snmp Getcomm Server Information CommandsServer Information Commands Description Sample Output SET Port S1 Stop 1SET Snmp LOCation string Command Description Sample OutputSnmp is Enabled Serial server Firmware Ver .19 Boot Ver 16Mbit FlashService Commands Description Service CommandsSET Servi service name NAme Newname SET Servi service name FRMSET Servi service name FRS SET Servi service name IP ENable DIsablePOSTSCRIPT\0A String CommandsString Commands Description Enter LANGUAGE=TCP/IP Commands Description TCP/IP CommandsSET IP LPD Auto Bootp Rarp Dhcp StaticSET IP FTP SET IP HttpSET IP Tftp SET IP TCPFirmware Update Command Description Power Configuration CommandsFirmware Update Power Configuration Command DescriptionSET LOAd IP Aa.bb.cc.dd SET LOAd ENable DIsableFirmware load is disabled SET LOAd HOst NameHelp Commands Miscellaneous CommandsMiscellaneous Commands Appendix B Engineering Drawings Antenna Cable AssemblyElectrical Specifications for Antenna Vswr Electrical Specifications Parameter ValueSilex technology america, Inc