Silex technology SX-550 SET LOAd ENable DIsable, SET LOAd HOst Name, SET LOAd IP Aa.bb.cc.dd

Page 78

Command

 

Description

 

 

 

This command is used for diagnostic purposes only.

 

The default value is Disable.

 

Sample output:

 

 

SET LOAd (ENable DIsable ]

SET LOAd HOst

Sets the node name of the Netware boot host.

 

This command is used for diagnostic purposes only.

 

The default value is null>\

 

 

Sample output:

 

 

SET LOAd HOst

<name>

SET LOAd IP

Sets source computer IP address for TFTP get operation.

 

The default value is 0.0.0.0.

 

Sample output:

 

 

SET LOAd IP

aa.bb.cc.dd

SET LOAd

Sets filename on host for TFTP get update

SOftware

Sample output:

 

 

 

 

SET LOAd SOftware <filename>

SET LOAd TFTP

Initiates firmware update using TFTP get operation.

 

The TFTP server address must be set using SET LOAd IP and the filename using

 

SET LOAd SOftware. The server will reset after the firmware update is completed.

 

Sample output:

 

 

SET LOAd TFTP

 

SET LOAd

Initiates firmware update using the XModem protocol on the serial console

XModem

The server will reset after the firmware update is completed.

 

 

Sample output:

 

 

SET LOAd XModem

SH LOAd

Shows the firmware update parameters

 

Sample output:

 

 

Firmware load is disabled

 

Load Host IP

= 0.0.0.0

 

Software file

= xxxx.bin

 

Load Host Name =

Page 72

silex

Console Commands

 

Part Number 40183-101

 

Page 77 Page 79
Image 78
Page 77 Page 79
Contents Developer’s Reference Guide Trademarks Contents Configuring Serial Port Monitor Alert and Trap Configuration Figures Silex Contents Part Number Safety Precautions About This Reference GuideEmissions Disclaimer Silex About This Reference Guide Part Number Processor and Wireless LAN Radio PCB IntroductionSilex Introduction Part Number Installing Wlan Module in Daughtercard Chapter Getting StartedVerify Development Kit Contents Installing the SX-550 Wlan Module Wlan Module Inserted in DaughtercardSX-550 Evaluation Daughtercard Monitoring Module Status Status Monitors Function StateOEM Interface Pinout Signal OEM InterfaceFunction State Status OEM Interface Signal Description Pin Type Power Management Electrical CharacteristicsPower Input Serial Peripheral InterfaceLogical Serial Port Signal Descriptions Pin Input/Output Serial PortsGround General Purpose IO Signal Descriptions Pin Selectable General Purpose IOLED and Gpio Descriptions LEDs and General Purpose IO SignalsEvaluation CN210 Drive High/Low Description Daughtercard GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7Additional OEM Interface Signals RS-232 CableOEM Interface Electrical Characteristics UART0TXD, UART0RTS UART1TXD, UART1RTSChapter Using the SX-550 Wlan Module Using the Wireless MethodEvaluation Module Connections Access silex Console Interface Using the Wired Ethernet MethodPort Settings Parameter Generating Configuration Data Pushbutton FunctionsAction Result Silex Using the SX-550 Wlan Module Part Number Chapter Accessing Configuration Parameters Access ExtendView UtilityInstalling ExtendView Utility Using ExtendView Utility ExtendView MainCreate View with Default Settings Access Http Pages ExtendView Configuration WindowAccess Internal Command Console SX-550 HomeUsing Telnet Session Using Terminal Emulator through the Serial PortTelnet Where x.x.x.x is the IP address of the SX-550 module Using AT Modem Commands Standard AT Commands SupportedAT Commands Parameter Description Response Codes Parameter Command DescriptionExtended AT Commands Parameter Description AT#Cset nw ssid silex#CsaveFactory Default Settings Parameter Description Chapter Setting Configuration ParametersFactory Default Settings CTS/RTSChanging Serial Settings Modify Basic SettingsRestoring Factory Default Settings Parameter Description Settings Default SettingSerial Setting Parameters Parameter SettingModifying TCP/IP Settings TCP/IP WindowTCP/IP Settings Change Password WindowTCP/IP Configuration Settings Parameter DNSConfigure Simple Network Management Protocol Snmp CommandsCommand Description Configuring Gpio Alerts and Traps Snmp Trap Settings ParameterGpio Commands Description Show Gpio DIRSET Gpio DIR in OUT Gpio # Gpio Trigger Commands Description Show Gpio SpecialSET Gpio Special ENA/DIS Gpio Transmit Commands Description Trig # Email String Gpio #1 is Gpio #2 isTrig # Email String Your email text msg here Gpio #2 is Port Monitor Alert Commands Description Show Port S1 TrigmonIndex # Monitor String Index # Xmit String Trigmon Commands DescriptionShow Port S1 Trigxmt Index # Xmit String Trigger string was seenOEM Header Interface Pinout Signal Designing with the SX-550OEM Header Interface Differential Output Ethernet Transmit Data primary Antenna Connectors Transformer Specification Ethernet PHYYCL General Purpose I/O Interface10/100M Magnetics Manufacturers Part Number GTSPower 40-Pin Drive High/Low DescriptionComponent Specifications Chapter Product SpecificationsProduct Specifications Radio Performance Specifications ParameterParameter Specifications TKIP, AESReceiver Sensitivity Production Specification TCP Port Connections TCP Port ConnectionsPort Destination Device Network Commands Description Appendix a Console CommandsWireless and Network Security Commands SET NW AUTHtype Open Shared Ttls Leap WPA-PSKSET NW ENC SET NW KEY#SET NW RTS Common name SET NW CertcnName User defined SET NW CERTCN2SET NW ID SET NW CertexpSET NW Certkey SET NW PWSET NW Wpagroup Enable Disable XON/XOFF RS232 Port CommandsPort Commands Description CL Port S1 JOBSET Port S1 Stop 1 Server Information CommandsServer Information Commands Description Sample Output SET Snmp GetcommSerial server Firmware Ver .19 Boot Ver 16Mbit Flash Command Description Sample OutputSnmp is Enabled SET Snmp LOCation stringService Commands Service Commands DescriptionSET Servi service name IP ENable DIsable SET Servi service name FRMSET Servi service name FRS SET Servi service name NAme NewnameEnter LANGUAGE= String CommandsString Commands Description POSTSCRIPT\0ATCP/IP Commands TCP/IP Commands Description SET IP Http Auto Bootp Rarp Dhcp Static SET IP FTP SET IP LPDSET IP TCP SET IP TftpPower Configuration Command Description Power Configuration CommandsFirmware Update Firmware Update Command DescriptionSET LOAd HOst Name SET LOAd ENable DIsableFirmware load is disabled SET LOAd IP Aa.bb.cc.ddMiscellaneous Commands Help CommandsMiscellaneous Commands Antenna Cable Assembly Appendix B Engineering DrawingsElectrical Specifications for Antenna Electrical Specifications Parameter Value VswrSilex technology america, Inc
Top Page Image Contents