Ultra electronic Prima 2e Cassette and/or the ink ribbon cassette, Setting cards, Inserting cards

Page 19

Set-up(continued)

Caution when loading the retransfer film

cassette and/or the ink ribbon cassette

The following caution shall be kept when the retransfer

film cassette and/or the ink ribbon cassette is removed

because of card jam or other trouble.

Please pay enough attention so that the retransfer film and/or ink ribbon is maintained at the right position. Particulary, the ink ribbon is extremely thin, therefore it apt to slip down when the cassette is removed as

shown in the illustration.

Improper Winding

Setting cards

Please use cards specified by your dealer. This unit can take both 0.76 mm(0.03inches)-thick and 0.25 mm (0.01inches)-thick cards. The factory setting is for 0.76 mm-thickness.

CAUTION

Fingerprints, soiling, etc. on card surface can result in print errors. Wear lint-free gloves when handling.

Inserting cards

Adjust the position with hands so that the media position of take-up side and supply side becomes parallel

When loaded in this condition, it may cause improper printing such as INK RUNOUT error, improper color printing etc.

To avoid this, please handle the ink ribbon and/or the retransfer film very carefully with hands so that the media position of take-up side become parallel.

Please do not touch the print side of the ink ribbon and/ or the retransfer film with your hands. Otherwise, it may cause improper printing.

When adjusting the print position of the retransfer film and/or ink ribbon, please follow the instruction label attached on the cassettes.

The unit can take about 300 0.76mm-thick cards.

As for 0.25mm thick cards do not insert more than 300 pcs.

This 300 pcs. is not a guaranteed quantity.

In the event of card feed failure, caused by card bending or others reduce card quantity.

CAUTION

When removing new cards from the box, it is possible that cards may be stuck due to static electricity. In this case, peel the cards off one at a time before setting into position. Hold the edges of the card when carrying out these operations.

1. Open the card tray.

Hold the lower part of the card tray and pull the tray toward you slowly until it no longer moves.

19

Image 19
Contents See p.42~43 See p.11~13,22See p.23~35 See p.19~21Declaration of Conformity Machine noise Operation is subject to the following two conditionsContents Do not wet the machine with water Do not touch the power plug during electrical stormsManual any time as you need Do not use a line voltage other than instructedDo not touch the power plug with a wet hand Do not use the machine while it has a faultPull out the power plug before cleaning the machine Hold the body of the power plug when pulling it outHandling of transfer film Ink ribbons and cards Product featuresChecking accessories Before useEscape Clause Do not place objects on top InstallationInstallation diagram 35% to 70%Names of parts Set-up Connecting the IC unit Sold separatelyMake sure to tighten the screws of the interface cables Malfunction of the product Connecting the LaminatorInstall the unit connecting cable.optional Product may occurCheck the plug For AC 120V type Connecting the power cordNorth America Europe Side Installing the card stackerHang the stacker claw on the stacker receptacle Card stacker is capable of containing approximatelyDo not touch the surface of the ink ribbon with your hands Setting the ink ribbonRemove the ink ribbon cassette Place the cassette upright on a flat surface during set-upAppears on the LCD panel When the ink ribbon is wound up to the endClose the printer door Insert the cassette along the guide railOtherwise the printer may fail Slowly Setting the retransfer filmActivate the slide knob and open the printer door Insert the retransfer film into the cassetteIf the retransfer film is not set properly When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassetteInserting cards Setting cardsCassette and/or the ink ribbon cassette Shown in the illustrationConsult your dealer to purchase new gloves When moving the card bracketFor ISO cards When using magnetic cardsSwitching the card thickness For JIS II cardsConnect the printer and host computer with the USB cable Connecting with a host computerConnecting Multiple Printers When connecting a host computer to multiple printersNames of parts on the operation panel BeforeuseLCD operation display content Operation display LED contentsLCD panel Operation display LED Ready LED will light up Turning on the powerDo not turn the power off while OperationIs loaded Turning off the powerUser modes User mode screen flowMain menu Press To save Displayed when the power is turned onCounter select mode Color settingsClearing the free counter Cleaning modeSee p.38,39 and p.40 for executing the cleaning mode Press to resetInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Unit No Setting Coercivity setting mode Test printNon-contact IC antenna setting mode IC contact setting modeClose the card tray CareandcleaningCleaning the cleaning rollers Open the card tray Remove the cleaning unitWipe the head indicated with Cleaning the thermal headCleaning the fan filter See p.15, 17 in this manualSee p.30 in this manual Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions If the sponge is removed, attach it again as shown belowConfirm that the retransfer film cassette has been removed Cleaning the magnetic headSet a cleaning card MoreOnce printer servicing and cleaning Have been completed Cleaning of the bobbin holdersPeriodical Maintenance Feed roller TroubleshootingAll rollers require routine cleaning Layout of rollers inside the printerTo initialize the unit Error code listingMG mechanical error Hardware errorError MG connection errorMending broken ink ribbon Retransfer film Stopping when printingAbout printing errors When retransfer operation is not completeHopper jam Pull out the card tray Removing card jamsInjury Retransfer section Jam transfer Specifications 343 381 External appearance and dimensionsFront view Side view Unit/mmSoftware License Agreement Page End of Agreement USA