Ultra electronic Prima 2e instruction manual Cleaning the magnetic head, Set a cleaning card, More

Page 39

Cleaning card (accessory)

Care and Cleaning	(continued)

5. Set a cleaning card.

Peel off the protective paper of the cleaning card and insert it into the NG card discharge slot. The card will be drawn into the unit by the rollers and cleaning will then be carried out from card discharge slot on the left side of the printer. Insert the card with its adhesive face upside down to repeat the cleaning procedure once

more.

The cleaning card can be inserted only from the right side.

NG card discharge slot

CAUTION

• If the retransfer roller (heat roller)

gets too hot,

H R i s t o o h o t !

appears on the LCD panel, and the printer returns to the Ready state.

Turn off the power of the printer, and wait until the roller completely cools down before starting the work.

Confirm that the retransfer film cassette has been removed.

•The cleaning card does not go into the card discharge slot at the left side.

•If a card jam occurs, turn off the power, then turn on the power again. The jammed card will be discarded.

6.Turn off the power after the cleaning card is discharged.

Wait for 10 seconds before turning on the power again.

CAUTION

The cleaning card can be used only once and disposable after using. If you use the dirty

cleaning card many times, the dirt on the card moves onto the rollers, causing damages to the rollers. Consult your dealer for the cleaning card.

Cleaning the magnetic head

Dirty magnetic head will cause a write/read error. It is recommended to clean the magnetic head after printing about 1,000 cards. Cleaning the magnetic head is not necessary if the magnetic stripe card is not used.

1. Keep the ink ribbon and retransfer film cassettes in their mounting positions.

2. Comfirm that the READY LED(Green) is lighted

3. Specify the “cleaning” mode in the user mode.

See p.27 in this manual.

> U s e r M o d e

MENU

> C l e a n i n g >

4.Apply alcohol on the magnetic head cleaning card. Drip three or four drops of alcohol on the magnetic stripes.

Alcohol (sold separately)

Magnetic head cleaning card (sold separately)

39

Image 39

Contents See p.42~43 See p.11~13,22See p.23~35 See p.19~21Declaration of Conformity Machine noise Operation is subject to the following two conditionsContents Do not wet the machine with water Do not touch the power plug during electrical stormsManual any time as you need Do not use a line voltage other than instructedDo not touch the power plug with a wet hand Do not use the machine while it has a faultPull out the power plug before cleaning the machine Hold the body of the power plug when pulling it outHandling of transfer film Ink ribbons and cards Product featuresChecking accessories Before useEscape Clause Do not place objects on top InstallationInstallation diagram 35% to 70%Names of parts Connecting the IC unit Sold separately Set-upMake sure to tighten the screws of the interface cables Malfunction of the product Connecting the LaminatorInstall the unit connecting cable.optional Product may occurConnecting the power cord Check the plug For AC 120V typeNorth America Europe Side Installing the card stackerHang the stacker claw on the stacker receptacle Card stacker is capable of containing approximatelyDo not touch the surface of the ink ribbon with your hands Setting the ink ribbonRemove the ink ribbon cassette Place the cassette upright on a flat surface during set-upAppears on the LCD panel When the ink ribbon is wound up to the endClose the printer door Insert the cassette along the guide railOtherwise the printer may fail Slowly Setting the retransfer filmActivate the slide knob and open the printer door Insert the retransfer film into the cassetteIf the retransfer film is not set properly When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassetteInserting cards Setting cardsCassette and/or the ink ribbon cassette Shown in the illustrationConsult your dealer to purchase new gloves When moving the card bracketFor ISO cards When using magnetic cardsSwitching the card thickness For JIS II cardsConnect the printer and host computer with the USB cable Connecting with a host computerConnecting Multiple Printers When connecting a host computer to multiple printersNames of parts on the operation panel BeforeuseOperation display LED contents LCD operation display contentLCD panel Operation display LED Ready LED will light up Turning on the powerDo not turn the power off while OperationIs loaded Turning off the powerUser modes User mode screen flowMain menu Press To save Displayed when the power is turned onCounter select mode Color settingsClearing the free counter Cleaning modeSee p.38,39 and p.40 for executing the cleaning mode Press to resetInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Unit No Setting Coercivity setting mode Test printNon-contact IC antenna setting mode IC contact setting modeClose the card tray CareandcleaningCleaning the cleaning rollers Open the card tray Remove the cleaning unitWipe the head indicated with Cleaning the thermal headCleaning the fan filter See p.15, 17 in this manualSee p.30 in this manual Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions If the sponge is removed, attach it again as shown belowConfirm that the retransfer film cassette has been removed Cleaning the magnetic headSet a cleaning card MoreCleaning of the bobbin holders Once printer servicing and cleaning Have been completedPeriodical Maintenance Feed roller TroubleshootingAll rollers require routine cleaning Layout of rollers inside the printerTo initialize the unit Error code listingMG mechanical error Hardware errorError MG connection errorMending broken ink ribbon Retransfer film Stopping when printingAbout printing errors When retransfer operation is not completeHopper jam Pull out the card tray Removing card jamsInjury Retransfer section Jam transfer Specifications 343 381 External appearance and dimensionsFront view Side view Unit/mmSoftware License Agreement Page End of Agreement USA