Ultra electronic Prima 2e instruction manual Specifications

Page 47

Specifications

Main specifications

CX21ICL Series (Large-type IC unit)

Power supply

: Fed from the printer.

DC 5V ± 5%, DC 12V

±

5%, DC 24V ± 5%

Recording method

: Sublimation type retransfer

Current dissipation

: 500mA, 300mA, 1A

Feed format

: Automatic feed

Mass

: 3.5kg

⋅

⋅

Recording density

:

300 dpi

Dimension (mm)

: 110(W)

221(D)

255(H)

Expression gradation

: 256 for Y, M, C and 2 for Bk

Accessories

: Joint plate

⋅ 1

⋅ 1

Inter-unit cable

Interface

: USB2.0(Hi-speed)

CX21ICS Series (Compact IC unit)

Operating environment conditions

° C ~ 30

° C

Power supply

: Fed from the printer.

Temperature: 15

Mass

: 0.5kg

⋅

⋅

Humidity: 35% ~ 70%

Dimension (mm)

: 50(W)

152(D)

115(H)

(no condensation)

Accessories

: Screw (with washer)

⋅ 3

Storage environment conditions

° C ~ 55

° C

Screw (without washer)

⋅ 2

Temperature: -15

Humidity: 20% ~ 80%

Power supply

: 100~120ACV/220~240ACV

(allowance

± 10%)

Current dissipation

:

7.0A (for 100V system)/5.0A (for

200V system)

Mass

: Standard 22kg

Excluding the built-in magnetic

encoder

Accessories

: Power cord for 120ACV

⋅ 1

(North America)

for 220~240ACV

⋅ 1

(Europe)

Manual(English)

⋅ 1

Cleaning card

⋅ 1

Card stacker

⋅ 1

Ink ribbon cassette

⋅ 1

Retransfer film cassette

⋅ 1

USB cable

⋅ 1

Jog lever (contained in the

⋅ 1

card tray)

Groves

⋅ 1

Products sold separately		: Cleaning card
: Ink ribbon(YMCK)		10 cards/set
•	1,000 frames/set	Model: CX210-CC1
	Model: DIC10216
Ink ribbon(YMCKK)
•	750 frames/set
	Model: DIC10217

Retransfer film •1000 frames/set

Model: DIC10085

: Compact IC unit Non-contact IC encoder

: Large-type IC unit

Mounts either a Non-contact or contact IC encoder.

The specifications and external appearance of this product are subject to change for improvements without a prior notice.

47

Image 47

Contents See p.42~43 See p.11~13,22See p.23~35 See p.19~21Declaration of Conformity Machine noise Operation is subject to the following two conditionsContents Do not wet the machine with water Do not touch the power plug during electrical stormsManual any time as you need Do not use a line voltage other than instructedDo not touch the power plug with a wet hand Do not use the machine while it has a faultPull out the power plug before cleaning the machine Hold the body of the power plug when pulling it outHandling of transfer film Ink ribbons and cards Product featuresChecking accessories Before useEscape Clause Do not place objects on top InstallationInstallation diagram 35% to 70%Names of parts Make sure to tighten the screws of the interface cables Connecting the IC unit Sold separatelySet-up Malfunction of the product Connecting the LaminatorInstall the unit connecting cable.optional Product may occurNorth America Europe Connecting the power cordCheck the plug For AC 120V type Side Installing the card stackerHang the stacker claw on the stacker receptacle Card stacker is capable of containing approximatelyDo not touch the surface of the ink ribbon with your hands Setting the ink ribbonRemove the ink ribbon cassette Place the cassette upright on a flat surface during set-upAppears on the LCD panel When the ink ribbon is wound up to the endClose the printer door Insert the cassette along the guide railOtherwise the printer may fail Slowly Setting the retransfer filmActivate the slide knob and open the printer door Insert the retransfer film into the cassetteIf the retransfer film is not set properly When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassetteInserting cards Setting cardsCassette and/or the ink ribbon cassette Shown in the illustrationConsult your dealer to purchase new gloves When moving the card bracketFor ISO cards When using magnetic cardsSwitching the card thickness For JIS II cardsConnect the printer and host computer with the USB cable Connecting with a host computerConnecting Multiple Printers When connecting a host computer to multiple printersNames of parts on the operation panel BeforeuseLCD panel Operation display LED contentsLCD operation display content Operation display LED Ready LED will light up Turning on the powerDo not turn the power off while OperationIs loaded Turning off the powerUser modes User mode screen flowMain menu Press To save Displayed when the power is turned onCounter select mode Color settingsClearing the free counter Cleaning modeSee p.38,39 and p.40 for executing the cleaning mode Press to resetInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Unit No Setting Coercivity setting mode Test printNon-contact IC antenna setting mode IC contact setting modeClose the card tray CareandcleaningCleaning the cleaning rollers Open the card tray Remove the cleaning unitWipe the head indicated with Cleaning the thermal headCleaning the fan filter See p.15, 17 in this manualSee p.30 in this manual Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions If the sponge is removed, attach it again as shown belowConfirm that the retransfer film cassette has been removed Cleaning the magnetic headSet a cleaning card MorePeriodical Maintenance Cleaning of the bobbin holdersOnce printer servicing and cleaning Have been completed Feed roller TroubleshootingAll rollers require routine cleaning Layout of rollers inside the printerTo initialize the unit Error code listingMG mechanical error Hardware errorError MG connection errorMending broken ink ribbon Retransfer film Stopping when printingAbout printing errors When retransfer operation is not completeHopper jam Pull out the card tray Removing card jamsInjury Retransfer section Jam transfer Specifications 343 381 External appearance and dimensionsFront view Side view Unit/mmSoftware License Agreement Page End of Agreement USA