Ultra electronic Prima 2e instruction manual When moving the card bracket

Page 20

Set-up(continued)

2. Pull the card bracket back.

The card bracket locks when it reaches the hole.

3. Insert the cards and move the bracket back into position.

Limit the number of cards as the card bracket moves back slightly from the lock position.

CAUTION Setting the cards improperly can cause feed jams. Check that the cards are neatly arranged.

Align the cards neatly with the side

Be sure that the tops of the cards are aligned properly

CAUTION

When moving the card bracket

back into position, do this slowly to avoid jamming your fingers. Leaving the card bracket out of position may cause card jams.

4. Close the card tray.

Push the card tray back into the printer until it no longer moves.

CAUTION

To print pre-printed cards on this printer, determine print layout, color tone and card inserting direction by in advance consulting your

dealear.

especially for card pre-printed in a dark color such as black, card positioning error may happen.

And for a magnetic or IC card, encoding error may happen.

CAUTION

When handling cards, avoid dusty environment and use the attached gloves.

Dusty cards such as those fingermarked may cause improper printing.

Consult your dealer to purchase new gloves.

20

Image 20

Contents See p.11~13,22 See p.23~35See p.19~21 See p.42~43Declaration of Conformity Operation is subject to the following two conditions Machine noiseContents Do not touch the power plug during electrical storms Manual any time as you needDo not use a line voltage other than instructed Do not wet the machine with waterDo not use the machine while it has a fault Pull out the power plug before cleaning the machineHold the body of the power plug when pulling it out Do not touch the power plug with a wet handProduct features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cardsEscape Clause Installation Installation diagram35% to 70% Do not place objects on topNames of parts Make sure to tighten the screws of the interface cables Connecting the IC unit Sold separatelySet-up Connecting the Laminator Install the unit connecting cable.optionalProduct may occur Malfunction of the productNorth America Europe Connecting the power cordCheck the plug For AC 120V type Installing the card stacker Hang the stacker claw on the stacker receptacleCard stacker is capable of containing approximately SideSetting the ink ribbon Remove the ink ribbon cassettePlace the cassette upright on a flat surface during set-up Do not touch the surface of the ink ribbon with your handsWhen the ink ribbon is wound up to the end Close the printer doorInsert the cassette along the guide rail Appears on the LCD panelSetting the retransfer film Activate the slide knob and open the printer doorInsert the retransfer film into the cassette Otherwise the printer may fail SlowlyWhen the retransfer film is wound up to the end Wind the retransfer film to take up the slackOpen the printer door and insert the cassette If the retransfer film is not set properlySetting cards Cassette and/or the ink ribbon cassetteShown in the illustration Inserting cardsWhen moving the card bracket Consult your dealer to purchase new glovesWhen using magnetic cards Switching the card thicknessFor JIS II cards For ISO cardsConnecting with a host computer Connecting Multiple PrintersWhen connecting a host computer to multiple printers Connect the printer and host computer with the USB cableBeforeuse Names of parts on the operation panelLCD panel Operation display LED contentsLCD operation display content Turning on the power Do not turn the power off whileOperation Operation display LED Ready LED will light upTurning off the power Is loadedUser mode screen flow User modesMain menu Displayed when the power is turned on Counter select modeColor settings Press To saveCleaning mode See p.38,39 and p.40 for executing the cleaning modePress to reset Clearing the free counterInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Coercivity setting mode Test print Non-contact IC antenna setting modeIC contact setting mode Unit No SettingCareandcleaning Cleaning the cleaning rollersOpen the card tray Remove the cleaning unit Close the card trayCleaning the thermal head Cleaning the fan filterSee p.15, 17 in this manual Wipe the head indicated withCleaning the card feed rollers and heat Rollers Install the fan filters back to the original positionsIf the sponge is removed, attach it again as shown below See p.30 in this manualCleaning the magnetic head Set a cleaning cardMore Confirm that the retransfer film cassette has been removedPeriodical Maintenance Cleaning of the bobbin holdersOnce printer servicing and cleaning Have been completed Troubleshooting All rollers require routine cleaningLayout of rollers inside the printer Feed rollerError code listing To initialize the unitHardware error ErrorMG connection error MG mechanical errorStopping when printing About printing errorsWhen retransfer operation is not complete Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications External appearance and dimensions Front viewSide view Unit/mm 343 381Software License Agreement Page End of Agreement USA