Ultra electronic Prima 2e instruction manual Buzzer mode setting

Page 33

Operation (continued)

Buzzer mode setting

Power saving mode settings

The buzzer indicating errors can be turned on or off.

> B u z z e r

EXIT

Exit user mode

O n

Set the buzzer:

there are two settings

(On, off)

			ENTER
Press			to select the setting and press	to save.
	(The electronic beep sounds.The beep will not sound

if the buzzer mode setting is set to off.)

When Off is specified,

•electronic beep sound indicating an error,

•electronic beep sound indicating the number of cards, and

•electronic beep sound indicating settings saved with the ENTER button in the user mode are muted.

The printer enters into the power save mode after a specified period of time if none of operation buttons are touched in the Ready state. The heat roller for retransfer, bend remedial roller, and back-light of the LCD panel are turned off in the power save mode.

> P o w e r S a v i n g

EXIT

Exit user mode

o f f

Power saving settings:

there are 9 options.

				ENTER
Press				to select the setting and press	to save.
	(The electronic beep sounds.The beep will not sound

if the buzzer mode setting is set to off.)

Press the EXIT button to cancel the user mode, and the printer starts.

Off:

Not in power saving mode.

Setting options: [5,10,15,20,25,30,45,60] (units: minutes) If printing is not to be carried out for a period longer than the

set time, switch the unitís heater off. (Power save status)

“Sleeping” appears on the LCD panel in the power save mode. The operation buttons are disabled in this mode. See step 2 in “Canceling the power save mode” to enable the operation buttons.

S l e e p i n g

The printer moves to the power save mode when the specified time arrives even if you turns off the printer and turn it on again.

Canceling the power save mode 1. From the host computer

Enter a control command to print the card. The power save mode is cancelled, and printing automatically starts upon completion of preheating.

2. Temporary cancellation

To cancel the power save mode temporarily on the

printer, press	RESET	, then	ENTER	to initialize the printer.

3. Permanent cancellation

Cancel the power save mode temporarily as described in step 2, and change the power save mode setting to OFF.

33

Image 33

Contents See p.23~35 See p.11~13,22See p.19~21 See p.42~43Declaration of Conformity Machine noise Operation is subject to the following two conditionsContents Manual any time as you need Do not touch the power plug during electrical stormsDo not use a line voltage other than instructed Do not wet the machine with waterPull out the power plug before cleaning the machine Do not use the machine while it has a faultHold the body of the power plug when pulling it out Do not touch the power plug with a wet handChecking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cardsEscape Clause Installation diagram Installation35% to 70% Do not place objects on topNames of parts Connecting the IC unit Sold separately Set-upMake sure to tighten the screws of the interface cables Install the unit connecting cable.optional Connecting the LaminatorProduct may occur Malfunction of the productConnecting the power cord Check the plug For AC 120V typeNorth America Europe Hang the stacker claw on the stacker receptacle Installing the card stackerCard stacker is capable of containing approximately SideRemove the ink ribbon cassette Setting the ink ribbonPlace the cassette upright on a flat surface during set-up Do not touch the surface of the ink ribbon with your handsClose the printer door When the ink ribbon is wound up to the endInsert the cassette along the guide rail Appears on the LCD panelActivate the slide knob and open the printer door Setting the retransfer filmInsert the retransfer film into the cassette Otherwise the printer may fail SlowlyWind the retransfer film to take up the slack When the retransfer film is wound up to the endOpen the printer door and insert the cassette If the retransfer film is not set properlyCassette and/or the ink ribbon cassette Setting cardsShown in the illustration Inserting cardsConsult your dealer to purchase new gloves When moving the card bracketSwitching the card thickness When using magnetic cardsFor JIS II cards For ISO cardsConnecting Multiple Printers Connecting with a host computerWhen connecting a host computer to multiple printers Connect the printer and host computer with the USB cableNames of parts on the operation panel BeforeuseOperation display LED contents LCD operation display contentLCD panel Do not turn the power off while Turning on the powerOperation Operation display LED Ready LED will light upIs loaded Turning off the powerUser modes User mode screen flowMain menu Counter select mode Displayed when the power is turned onColor settings Press To saveSee p.38,39 and p.40 for executing the cleaning mode Cleaning modePress to reset Clearing the free counterInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Non-contact IC antenna setting mode Coercivity setting mode Test printIC contact setting mode Unit No SettingCleaning the cleaning rollers CareandcleaningOpen the card tray Remove the cleaning unit Close the card trayCleaning the fan filter Cleaning the thermal headSee p.15, 17 in this manual Wipe the head indicated withInstall the fan filters back to the original positions Cleaning the card feed rollers and heat RollersIf the sponge is removed, attach it again as shown below See p.30 in this manualSet a cleaning card Cleaning the magnetic headMore Confirm that the retransfer film cassette has been removedCleaning of the bobbin holders Once printer servicing and cleaning Have been completedPeriodical Maintenance All rollers require routine cleaning TroubleshootingLayout of rollers inside the printer Feed rollerTo initialize the unit Error code listingError Hardware errorMG connection error MG mechanical errorAbout printing errors Stopping when printingWhen retransfer operation is not complete Mending broken ink ribbon Retransfer filmHopper jam Pull out the card tray Removing card jamsInjury Retransfer section Jam transfer Specifications Front view External appearance and dimensionsSide view Unit/mm 343 381Software License Agreement Page End of Agreement USA