Ultra electronic Prima 2e When using magnetic cards, For JIS II cards, For ISO cards

Page 21

Set-up(continued)

When using magnetic cards

When using cards with magnetic strips, set the cards in the following manner.

For JIS II cards:

Place the card with its magnetic stripes upward and facing the card bracket.

For ISO cards:

Place the card with its magnetic stripes downward and facing the card bracket.

CAUTION

Printing on cards with magnetic strips is not guaranteed.

When using contact IC cards

When using contact IC cards, set in the following manner.

Place the IC card with its IC terminal inward and facing the card bracket.

Loading cards

Load cards when the printer’s LCD panel shows the message “Ready” or “No Card”, and not when printer operations have stopped due to an error. Cards can

also be loaded when the power supply is not switched on. If there is a drop in the volume of remaining cards (under about 25 cards with a thickness of 0.76mm), the electronic beep sounds before every feeding.

(See p.33 in this manual.)

R e a d y

N o C a r d

OR

L o a d i n g

When “Loading” is displayed on the LCD panel, do not open the card tray under any circumstances.

The unit is currently feeding cards. If a message other than the one above is displayed, cards can be loaded even while the unit is printing. However, you are recommended to load cards when the unit is not printing.

To prevent defective printing caused by suspended printing or vibration as a result of opening and closing the card tray, load cards with care.

Switching the card thickness

Depending on the material, some 0.25mm(0.01inches) thick cards may not be suitable for printing. Consult your dealer regarding the materials and specifications of the card before purchasing.

WARNING

•As for switching the card thickness,consult your dealer or the service personnel. Otherwise injuries or malfunction of the printer may be caused

Electric shock

Injury

21

Image 21

Contents See p.23~35 See p.11~13,22See p.19~21 See p.42~43Declaration of Conformity Machine noise Operation is subject to the following two conditionsContents Manual any time as you need Do not touch the power plug during electrical stormsDo not use a line voltage other than instructed Do not wet the machine with waterPull out the power plug before cleaning the machine Do not use the machine while it has a faultHold the body of the power plug when pulling it out Do not touch the power plug with a wet handChecking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cardsEscape Clause Installation diagram Installation35% to 70% Do not place objects on topNames of parts Connecting the IC unit Sold separately Set-upMake sure to tighten the screws of the interface cables Install the unit connecting cable.optional Connecting the LaminatorProduct may occur Malfunction of the productConnecting the power cord Check the plug For AC 120V typeNorth America Europe Hang the stacker claw on the stacker receptacle Installing the card stackerCard stacker is capable of containing approximately SideRemove the ink ribbon cassette Setting the ink ribbonPlace the cassette upright on a flat surface during set-up Do not touch the surface of the ink ribbon with your handsClose the printer door When the ink ribbon is wound up to the endInsert the cassette along the guide rail Appears on the LCD panelActivate the slide knob and open the printer door Setting the retransfer filmInsert the retransfer film into the cassette Otherwise the printer may fail SlowlyWind the retransfer film to take up the slack When the retransfer film is wound up to the endOpen the printer door and insert the cassette If the retransfer film is not set properlyCassette and/or the ink ribbon cassette Setting cardsShown in the illustration Inserting cardsConsult your dealer to purchase new gloves When moving the card bracketSwitching the card thickness When using magnetic cardsFor JIS II cards For ISO cardsConnecting Multiple Printers Connecting with a host computerWhen connecting a host computer to multiple printers Connect the printer and host computer with the USB cableNames of parts on the operation panel BeforeuseOperation display LED contents LCD operation display contentLCD panel Do not turn the power off while Turning on the powerOperation Operation display LED Ready LED will light upIs loaded Turning off the powerUser modes User mode screen flowMain menu Counter select mode Displayed when the power is turned onColor settings Press To saveSee p.38,39 and p.40 for executing the cleaning mode Cleaning modePress to reset Clearing the free counterInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Non-contact IC antenna setting mode Coercivity setting mode Test printIC contact setting mode Unit No SettingCleaning the cleaning rollers CareandcleaningOpen the card tray Remove the cleaning unit Close the card trayCleaning the fan filter Cleaning the thermal headSee p.15, 17 in this manual Wipe the head indicated withInstall the fan filters back to the original positions Cleaning the card feed rollers and heat RollersIf the sponge is removed, attach it again as shown below See p.30 in this manualSet a cleaning card Cleaning the magnetic headMore Confirm that the retransfer film cassette has been removedCleaning of the bobbin holders Once printer servicing and cleaning Have been completedPeriodical Maintenance All rollers require routine cleaning TroubleshootingLayout of rollers inside the printer Feed rollerTo initialize the unit Error code listingError Hardware errorMG connection error MG mechanical errorAbout printing errors Stopping when printingWhen retransfer operation is not complete Mending broken ink ribbon Retransfer filmHopper jam Pull out the card tray Removing card jamsInjury Retransfer section Jam transfer Specifications Front view External appearance and dimensionsSide view Unit/mm 343 381Software License Agreement Page End of Agreement USA