Ultra electronic Prima 2e instruction manual Installing the card stacker, Side

Page 14

Set-up(continued)

Installing the card stacker

Hang the stacker claw on the stacker receptacle.

Card discharge slot

Claw	Card stacker
	receptacle
Card stacker
(accessory)

The card stacker is capable of containing approximately

100 0.76mm(0.03inches)-thick cards or 300 0.25mm (0.01inches)-thick cards at the maximum.

CAUTION

Be sure to hang the card stacker claw

on the card stacker receptacle, not the card discharge slot. If you mount the card stacker at a wrong place, cards are not discharged, resulting in a card jam.

When connecting the laminator, pull the tab of the card stacker at the stacker mount of the laminator card.

Card discharge slot

Claw

Card stacker

Card Stackerreceptacle (accessory)

Discharging the card

When correctly printed, the cards are discharged from the left side.

If a card jam or a write error on magnetic stripes occurs on the way, results differ depending on the areas.

Portion A: If a card jam , a write error on magnetic stripes or an IC unit encord error occurs on the way, press the RESET button, then the ENTER button. The printer is initialized, and the cards are discharged from the right side of the printer.

Portion B: See the description in Jam (Transfer) on p.46.

Portion C: When correctly printed, the cards are


discharged from the left side		of the printer.
The cards jamming around this area are
also discharged from the left		side.
Retransfer film cassette	Ink ribbon cassette

Thermal head

Magnetic head

Card turnover

table Feed roller

NG card discharge slot

Cleaning roller

Card feed roller

Retransfer roller (heat roller)

Bent remedial roller (heat roller)

C BA

14

Image 14

Contents See p.19~21 See p.11~13,22See p.23~35 See p.42~43Declaration of Conformity Operation is subject to the following two conditions Machine noiseContents Do not use a line voltage other than instructed Do not touch the power plug during electrical stormsManual any time as you need Do not wet the machine with waterHold the body of the power plug when pulling it out Do not use the machine while it has a faultPull out the power plug before cleaning the machine Do not touch the power plug with a wet handBefore use Product featuresChecking accessories Handling of transfer film Ink ribbons and cardsEscape Clause 35% to 70% InstallationInstallation diagram Do not place objects on topNames of parts Make sure to tighten the screws of the interface cables Connecting the IC unit Sold separatelySet-up Product may occur Connecting the LaminatorInstall the unit connecting cable.optional Malfunction of the productNorth America Europe Connecting the power cordCheck the plug For AC 120V type Card stacker is capable of containing approximately Installing the card stackerHang the stacker claw on the stacker receptacle SidePlace the cassette upright on a flat surface during set-up Setting the ink ribbonRemove the ink ribbon cassette Do not touch the surface of the ink ribbon with your handsInsert the cassette along the guide rail When the ink ribbon is wound up to the endClose the printer door Appears on the LCD panelInsert the retransfer film into the cassette Setting the retransfer filmActivate the slide knob and open the printer door Otherwise the printer may fail SlowlyOpen the printer door and insert the cassette When the retransfer film is wound up to the endWind the retransfer film to take up the slack If the retransfer film is not set properlyShown in the illustration Setting cardsCassette and/or the ink ribbon cassette Inserting cardsWhen moving the card bracket Consult your dealer to purchase new glovesFor JIS II cards When using magnetic cardsSwitching the card thickness For ISO cardsWhen connecting a host computer to multiple printers Connecting with a host computerConnecting Multiple Printers Connect the printer and host computer with the USB cableBeforeuse Names of parts on the operation panelLCD panel Operation display LED contentsLCD operation display content Operation Turning on the powerDo not turn the power off while Operation display LED Ready LED will light upTurning off the power Is loadedUser mode screen flow User modesMain menu Color settings Displayed when the power is turned onCounter select mode Press To savePress to reset Cleaning modeSee p.38,39 and p.40 for executing the cleaning mode Clearing the free counterInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode IC contact setting mode Coercivity setting mode Test printNon-contact IC antenna setting mode Unit No SettingOpen the card tray Remove the cleaning unit CareandcleaningCleaning the cleaning rollers Close the card traySee p.15, 17 in this manual Cleaning the thermal headCleaning the fan filter Wipe the head indicated withIf the sponge is removed, attach it again as shown below Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions See p.30 in this manualMore Cleaning the magnetic headSet a cleaning card Confirm that the retransfer film cassette has been removedPeriodical Maintenance Cleaning of the bobbin holdersOnce printer servicing and cleaning Have been completed Layout of rollers inside the printer TroubleshootingAll rollers require routine cleaning Feed rollerError code listing To initialize the unitMG connection error Hardware errorError MG mechanical errorWhen retransfer operation is not complete Stopping when printingAbout printing errors Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications Side view Unit/mm External appearance and dimensionsFront view 343 381Software License Agreement Page End of Agreement USA