Ultra electronic Prima 2e Troubleshooting, Layout of rollers inside the printer, Feed roller

Page 41

Troubleshooting

Layout of rollers inside the printer

Below is a diagram of the layout of rollers inside the printer. Refer to this diagram in the event of card jams and when cleaning the rollers.

Retransfer film cassette

Ink ribbon cassette

			Thermal head
			Magnetic head
		Card turnover table
		Card feed rollers
		Card jams	(see p.46)
		J a m ( T u r n O v e r )
Card jams	(see p. 46)	Cleaning rollers
J a m ( T r a n s f e r )
			Card feed rollers
			Card jams	(see p.45)
			J a m ( H o p p e r )
Retransfer roller (heat roller)

Bend remedial roller (heat roller)

All rollers require routine cleaning.

•The card feed rollers, retransfer roller and bend remedial roller can be cleaned on cleaning mode.

(See p.38, 39 in this manual.)

•The cleaning roller can be cleaned by water washing.

(See p.36 in this manual.)

How to clean the feed roller

1.Open the card tray, and take out the cards from the tray.

2.Move the card bracket until it locks.

3.Clean the feed roller with felt (sold separately) soaked with absolute alcohol(ethanol).

Feed roller

41

Image 41

Contents See p.23~35 See p.11~13,22See p.19~21 See p.42~43Declaration of Conformity Machine noise Operation is subject to the following two conditionsContents Manual any time as you need Do not touch the power plug during electrical stormsDo not use a line voltage other than instructed Do not wet the machine with waterPull out the power plug before cleaning the machine Do not use the machine while it has a faultHold the body of the power plug when pulling it out Do not touch the power plug with a wet handChecking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cardsEscape Clause Installation diagram Installation35% to 70% Do not place objects on topNames of parts Make sure to tighten the screws of the interface cables Connecting the IC unit Sold separatelySet-up Install the unit connecting cable.optional Connecting the LaminatorProduct may occur Malfunction of the productNorth America Europe Connecting the power cordCheck the plug For AC 120V type Hang the stacker claw on the stacker receptacle Installing the card stackerCard stacker is capable of containing approximately SideRemove the ink ribbon cassette Setting the ink ribbonPlace the cassette upright on a flat surface during set-up Do not touch the surface of the ink ribbon with your handsClose the printer door When the ink ribbon is wound up to the endInsert the cassette along the guide rail Appears on the LCD panelActivate the slide knob and open the printer door Setting the retransfer filmInsert the retransfer film into the cassette Otherwise the printer may fail SlowlyWind the retransfer film to take up the slack When the retransfer film is wound up to the endOpen the printer door and insert the cassette If the retransfer film is not set properlyCassette and/or the ink ribbon cassette Setting cardsShown in the illustration Inserting cardsConsult your dealer to purchase new gloves When moving the card bracketSwitching the card thickness When using magnetic cardsFor JIS II cards For ISO cardsConnecting Multiple Printers Connecting with a host computerWhen connecting a host computer to multiple printers Connect the printer and host computer with the USB cableNames of parts on the operation panel BeforeuseLCD panel Operation display LED contentsLCD operation display content Do not turn the power off while Turning on the powerOperation Operation display LED Ready LED will light upIs loaded Turning off the powerUser modes User mode screen flowMain menu Counter select mode Displayed when the power is turned onColor settings Press To saveSee p.38,39 and p.40 for executing the cleaning mode Cleaning modePress to reset Clearing the free counterInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Non-contact IC antenna setting mode Coercivity setting mode Test printIC contact setting mode Unit No SettingCleaning the cleaning rollers CareandcleaningOpen the card tray Remove the cleaning unit Close the card trayCleaning the fan filter Cleaning the thermal headSee p.15, 17 in this manual Wipe the head indicated withInstall the fan filters back to the original positions Cleaning the card feed rollers and heat RollersIf the sponge is removed, attach it again as shown below See p.30 in this manualSet a cleaning card Cleaning the magnetic headMore Confirm that the retransfer film cassette has been removedPeriodical Maintenance Cleaning of the bobbin holdersOnce printer servicing and cleaning Have been completed All rollers require routine cleaning TroubleshootingLayout of rollers inside the printer Feed rollerTo initialize the unit Error code listingError Hardware errorMG connection error MG mechanical errorAbout printing errors Stopping when printingWhen retransfer operation is not complete Mending broken ink ribbon Retransfer filmHopper jam Pull out the card tray Removing card jamsInjury Retransfer section Jam transfer Specifications Front view External appearance and dimensionsSide view Unit/mm 343 381Software License Agreement Page End of Agreement USA