Ultra electronic Prima 2e Connecting with a host computer, Connecting Multiple Printers

Page 22

Set-up(continued)

Connecting with a host computer

CAUTION Do not switch off the power of the

host computer during printing.

Do not use the sleep or the stand-by function on the host computer.

If the power of the host computer is switched off during printing, or if the sleep or the stand-by function of the host computer is activated, the printer may stop with cards printed halfway remain

in the printer. When this occurs, initialize the priner as “Slopping when printing”of page 44 on this manual.

1. Check to ensure that the power of both the printer and host computer are switched off.

2. Connect the printer and host computer with the USB cable.

Insert the USB cable to the USB cable connection terminal at the back of the printer.

USB cable (Accessories)

CAUTION

Adjust orientation of the USB cable according to the terminal, and insert it all the way in.

CAUTION

Consult your dealer on the cable connection if there are USB or serial cable connection

terminal on the printer’s optional port.

CAUTION

The location of terminals varies with the host computer. Please refer to the instruction manual of the host computer.

When there are multiple USB cable comection terminal on the host computer, either one can be used.

Do not connect to the USB comection terminal on the host computer’s monitor or keyboard. It may not be recognized correctly.

When using a USB hub, connect to the hub that is directly linked to the host computer.

Connecting Multiple Printers

When connecting a host computer to multiple printers,

set different Unit Numbers from 1 to 7 for each printer. Refer to see the page 35 of the instruction manual

22

Image 22

Contents See p.19~21 See p.11~13,22See p.23~35 See p.42~43Declaration of Conformity Operation is subject to the following two conditions Machine noiseContents Do not use a line voltage other than instructed Do not touch the power plug during electrical stormsManual any time as you need Do not wet the machine with waterHold the body of the power plug when pulling it out Do not use the machine while it has a faultPull out the power plug before cleaning the machine Do not touch the power plug with a wet handBefore use Product featuresChecking accessories Handling of transfer film Ink ribbons and cardsEscape Clause 35% to 70% InstallationInstallation diagram Do not place objects on topNames of parts Set-up Connecting the IC unit Sold separatelyMake sure to tighten the screws of the interface cables Product may occur Connecting the LaminatorInstall the unit connecting cable.optional Malfunction of the productCheck the plug For AC 120V type Connecting the power cordNorth America Europe Card stacker is capable of containing approximately Installing the card stackerHang the stacker claw on the stacker receptacle SidePlace the cassette upright on a flat surface during set-up Setting the ink ribbonRemove the ink ribbon cassette Do not touch the surface of the ink ribbon with your handsInsert the cassette along the guide rail When the ink ribbon is wound up to the endClose the printer door Appears on the LCD panelInsert the retransfer film into the cassette Setting the retransfer filmActivate the slide knob and open the printer door Otherwise the printer may fail SlowlyOpen the printer door and insert the cassette When the retransfer film is wound up to the endWind the retransfer film to take up the slack If the retransfer film is not set properly Shown in the illustration Setting cards Cassette and/or the ink ribbon cassette Inserting cardsWhen moving the card bracket Consult your dealer to purchase new glovesFor JIS II cards When using magnetic cardsSwitching the card thickness For ISO cardsWhen connecting a host computer to multiple printers Connecting with a host computerConnecting Multiple Printers Connect the printer and host computer with the USB cableBeforeuse Names of parts on the operation panelLCD operation display content Operation display LED contentsLCD panel Operation Turning on the powerDo not turn the power off while Operation display LED Ready LED will light upTurning off the power Is loadedUser mode screen flow User modesMain menu Color settings Displayed when the power is turned onCounter select mode Press To savePress to reset Cleaning modeSee p.38,39 and p.40 for executing the cleaning mode Clearing the free counterInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode IC contact setting mode Coercivity setting mode Test printNon-contact IC antenna setting mode Unit No SettingOpen the card tray Remove the cleaning unit CareandcleaningCleaning the cleaning rollers Close the card traySee p.15, 17 in this manual Cleaning the thermal headCleaning the fan filter Wipe the head indicated withIf the sponge is removed, attach it again as shown below Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions See p.30 in this manualMore Cleaning the magnetic headSet a cleaning card Confirm that the retransfer film cassette has been removedOnce printer servicing and cleaning Have been completed Cleaning of the bobbin holdersPeriodical Maintenance Layout of rollers inside the printer TroubleshootingAll rollers require routine cleaning Feed rollerError code listing To initialize the unitMG connection error Hardware errorError MG mechanical errorWhen retransfer operation is not complete Stopping when printingAbout printing errors Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications Side view Unit/mm External appearance and dimensionsFront view 343 381Software License Agreement Page End of Agreement USA