Ultra electronic Prima 2e Cleaning of the bobbin holders, Periodical Maintenance

Page 40

Care and Cleaning

(continued)

5. Set the card on the card tray.

Place the card in right direction. See p.21.

6.	Press the ENTER button, select “MG Head” with
	the ↑ or ↓ button, and press the ENTER button.

		> > M G H e a d
				O K ?

		ENTER

C l e a n i n g . .

7. When the cleaning card is discharged from NG card discharge slot, turn off the power of the printer. Wait for 10 seconds before turning on the power again.

CAUTION

Replace the magnetic head cleaning card when it gets dirty. A dirty card may pollute the head

and cause damages to the head.

Consult your dealer on the alcohol and cleaning card.

Cleaning of the bobbin holders

Dirt on the bobbin holders may appear on the card or the film, cause defects on the card. Clean the bobbins when replacing ink ribbon or retransfer film.

1. Remove the cassettes of ink ribbon and retransfer film.

See p.15 and 17 of this manual.

2. Wipe 4 bobbin holders with “Kim-Wipe” soaked with absolute alcohol(ethanol)

Once printer servicing and cleaning

have been completed

Once servicing and cleaning of the printer have been completed, check to make sure that all parts have been replaced properly.

Improper replacement of parts may result in the power not turning on or in operating errors.

Periodical Maintenance

Periodical maintenance by the service personnel is recommended to avoid print error and failure. Consult your dealer for maintenance period and cost.

40

Image 40

Contents See p.11~13,22 See p.23~35See p.19~21 See p.42~43Declaration of Conformity Operation is subject to the following two conditions Machine noiseContents Do not touch the power plug during electrical storms Manual any time as you needDo not use a line voltage other than instructed Do not wet the machine with waterDo not use the machine while it has a fault Pull out the power plug before cleaning the machineHold the body of the power plug when pulling it out Do not touch the power plug with a wet handProduct features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cardsEscape Clause Installation Installation diagram35% to 70% Do not place objects on topNames of parts Set-up Connecting the IC unit Sold separatelyMake sure to tighten the screws of the interface cables Connecting the Laminator Install the unit connecting cable.optionalProduct may occur Malfunction of the productCheck the plug For AC 120V type Connecting the power cordNorth America Europe Installing the card stacker Hang the stacker claw on the stacker receptacleCard stacker is capable of containing approximately SideSetting the ink ribbon Remove the ink ribbon cassettePlace the cassette upright on a flat surface during set-up Do not touch the surface of the ink ribbon with your handsWhen the ink ribbon is wound up to the end Close the printer doorInsert the cassette along the guide rail Appears on the LCD panelSetting the retransfer film Activate the slide knob and open the printer doorInsert the retransfer film into the cassette Otherwise the printer may fail SlowlyWhen the retransfer film is wound up to the end Wind the retransfer film to take up the slackOpen the printer door and insert the cassette If the retransfer film is not set properlySetting cards Cassette and/or the ink ribbon cassetteShown in the illustration Inserting cardsWhen moving the card bracket Consult your dealer to purchase new glovesWhen using magnetic cards Switching the card thicknessFor JIS II cards For ISO cardsConnecting with a host computer Connecting Multiple PrintersWhen connecting a host computer to multiple printers Connect the printer and host computer with the USB cableBeforeuse Names of parts on the operation panelLCD operation display content Operation display LED contentsLCD panel Turning on the power Do not turn the power off whileOperation Operation display LED Ready LED will light upTurning off the power Is loadedUser mode screen flow User modesMain menu Displayed when the power is turned on Counter select modeColor settings Press To saveCleaning mode See p.38,39 and p.40 for executing the cleaning modePress to reset Clearing the free counterInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Coercivity setting mode Test print Non-contact IC antenna setting modeIC contact setting mode Unit No SettingCareandcleaning Cleaning the cleaning rollersOpen the card tray Remove the cleaning unit Close the card trayCleaning the thermal head Cleaning the fan filterSee p.15, 17 in this manual Wipe the head indicated withCleaning the card feed rollers and heat Rollers Install the fan filters back to the original positionsIf the sponge is removed, attach it again as shown below See p.30 in this manualCleaning the magnetic head Set a cleaning cardMore Confirm that the retransfer film cassette has been removedOnce printer servicing and cleaning Have been completed Cleaning of the bobbin holdersPeriodical Maintenance Troubleshooting All rollers require routine cleaningLayout of rollers inside the printer Feed rollerError code listing To initialize the unitHardware error ErrorMG connection error MG mechanical errorStopping when printing About printing errorsWhen retransfer operation is not complete Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications External appearance and dimensions Front viewSide view Unit/mm 343 381Software License Agreement Page End of Agreement USA