Ultra electronic Prima 2e instruction manual Injury Retransfer section Jam transfer

Page 46

Troubleshooting (continued)

Turnover section [Jam (turnover)]

1. Open the printer door and remove the ink ribbon cassette.

See p.15 in this manual.

2. Remove any jammed cards.

• If you can pull out the jammed cards, take them out.

•If the jammed cards come out of the turnover table, push them back into the table, and rotate the table slowly (as it is positioned vertically) until the table is located so that the cards can be taken out.

CAUTION

•When rotating the turnover table, be careful not to touch the metal edge. Wear a glove for this work.

Injury

Retransfer section [Jam (transfer)]

1. Open the printer door and remove the retransfer film cassette.

See p.17 in this manual.

2. A jog lever are supplied as standard.

The jog lever are attached to the center of the card tray

.	Jog lever

Turn the tabs in the arrow direction and take out the jog lever and removal stick.

3. Turn the jog dial to move the card to the position where it becomes visible.

Turn the jog dial with the attached jog lever.

4. Remove the card.

Remove the card.

CAUTION

Some parts inside the printer may be hot. Be careful when removing the card.

46

Image 46

Contents See p.19~21 See p.11~13,22See p.23~35 See p.42~43Declaration of Conformity Operation is subject to the following two conditions Machine noiseContents Do not use a line voltage other than instructed Do not touch the power plug during electrical stormsManual any time as you need Do not wet the machine with waterHold the body of the power plug when pulling it out Do not use the machine while it has a faultPull out the power plug before cleaning the machine Do not touch the power plug with a wet handBefore use Product featuresChecking accessories Handling of transfer film Ink ribbons and cardsEscape Clause 35% to 70% InstallationInstallation diagram Do not place objects on topNames of parts Set-up Connecting the IC unit Sold separatelyMake sure to tighten the screws of the interface cables Product may occur Connecting the LaminatorInstall the unit connecting cable.optional Malfunction of the productCheck the plug For AC 120V type Connecting the power cordNorth America Europe Card stacker is capable of containing approximately Installing the card stackerHang the stacker claw on the stacker receptacle SidePlace the cassette upright on a flat surface during set-up Setting the ink ribbonRemove the ink ribbon cassette Do not touch the surface of the ink ribbon with your handsInsert the cassette along the guide rail When the ink ribbon is wound up to the endClose the printer door Appears on the LCD panelInsert the retransfer film into the cassette Setting the retransfer filmActivate the slide knob and open the printer door Otherwise the printer may fail SlowlyOpen the printer door and insert the cassette When the retransfer film is wound up to the endWind the retransfer film to take up the slack If the retransfer film is not set properlyShown in the illustration Setting cardsCassette and/or the ink ribbon cassette Inserting cardsWhen moving the card bracket Consult your dealer to purchase new glovesFor JIS II cards When using magnetic cardsSwitching the card thickness For ISO cardsWhen connecting a host computer to multiple printers Connecting with a host computerConnecting Multiple Printers Connect the printer and host computer with the USB cableBeforeuse Names of parts on the operation panelLCD operation display content Operation display LED contentsLCD panel Operation Turning on the powerDo not turn the power off while Operation display LED Ready LED will light upTurning off the power Is loadedUser mode screen flow User modesMain menu Color settings Displayed when the power is turned onCounter select mode Press To savePress to reset Cleaning modeSee p.38,39 and p.40 for executing the cleaning mode Clearing the free counterInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode IC contact setting mode Coercivity setting mode Test printNon-contact IC antenna setting mode Unit No SettingOpen the card tray Remove the cleaning unit CareandcleaningCleaning the cleaning rollers Close the card traySee p.15, 17 in this manual Cleaning the thermal headCleaning the fan filter Wipe the head indicated withIf the sponge is removed, attach it again as shown below Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions See p.30 in this manualMore Cleaning the magnetic headSet a cleaning card Confirm that the retransfer film cassette has been removedOnce printer servicing and cleaning Have been completed Cleaning of the bobbin holdersPeriodical Maintenance Layout of rollers inside the printer TroubleshootingAll rollers require routine cleaning Feed rollerError code listing To initialize the unitMG connection error Hardware errorError MG mechanical errorWhen retransfer operation is not complete Stopping when printingAbout printing errors Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications Side view Unit/mm External appearance and dimensionsFront view 343 381Software License Agreement Page End of Agreement USA