Transcend Information III manual Bind IPX to X NET=XXXX Bind IPX to Y NET=XXXX

Page 44

Loading NetWare ODI Drivers 4-13

Driver Installation with NetWare

To load the 4.x server driver, follow these steps:

1Copy the contents of the appropriate \NETWARE subdirectory to the boot partition of the server’s hard disk.

2When you start the server, enter the following commands:

For NetWare 3.11:

LOAD C:LSLENH.NLM [Enter]

LOAD C:3C59X.LAN PORT=XXXX NAME=X [Enter] LOAD C:3C59X.LAN PORT=XXXX NAME=Y [Enter]

BIND IPX TO X NET=XXXX

BIND IPX TO Y NET=XXXX

For NetWare 3.12, 4.0x, or 4.x:

LOAD C:3C59X.LAN PORT=XXXX NAME=X [Enter] LOAD C:3C59X.LAN PORT=XXXX NAME=Y [Enter]

BIND IPX TO X NET=XXXX

BIND IPX TO Y NET=XXXX

where XXXX is the adapter’s port address and NAME X and Y are names that you assign to help distinguish the multiple adapters. (To determine the port address, refer to the previous section “Finding the Adapter’s Port Address for Multiple Adapters.”)

If the load sequence above is not followed, the system will not operate correctly. Make sure that the PORT XXXX parameter is completed for all adapters.

When running the 3C59X.LAN driver with NetWare 3.11, you must update the MONITOR.NLM ﬁle that accompanied NetWare 3.11 with the MONITOR.NLM ﬁle from Novell. For the latest NLMs, contact Novell.

Image 44

Contents Adapters 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Lifetime Warranty France, Israel Contents Performing Troubleshooting and Diagnostic Tests Cispr B Compliance Figures Tables Introduction How to Use This GuideAbout this Guide Conventions Print autolink.logIntroduction Features Optional Installing the Eisa AdapterInserting the Adapter Installing the Boot PromInspecting the Adapter PCI and Eisa Bus Slots in an Eisa Computer List of devices appears, arranged by type Conﬁrming Adapter InstallationName of the installed 3Com adapter appears, as shown below Connecting to Thin Ethernet Cable Connecting to the NetworkConnecting to the On-board Transceiver Connecting to an External Transceiver Slide Latch Auto Select Media Type Configuring Adapter Conﬁguration OverviewUsing a NOS Other Than Windows Conﬁguring the AdapterUsing Windows Software Option Settings Full Duplex Media TypeNetwork Driver Optimization Changing the Settings Type at the promptI N N U Continue this procedure with any of the other options Press Tab to highlight OK. Press EnterSelect Adapter Installed Adapters Loading Network DriversAccessing DOS Locating the Network DriversLoading NetWare ODI Drivers One Adapter in a ClientAutoLink Requirements At the prompt, type Alternatively, at the prompt, typeAutoLink Information Screen Multiple Adapters in a Client To print the ﬁle, typeWhen the program has ﬁnished a Save the conﬁguration Main menu appears Reboot the computer Finding the Adapter’s Slot NumberRepeat a for the second adapter One Adapter in a Server Multiple Adapters in a Server For NetWare 3.12, 4.0x, orFinding the Adapter’s Port Address for Multiple Adapters Bind IPX to X NET=XXXX Bind IPX to Y NET=XXXX Loading Windows 95 Drivers Click OK This imports the driver from the EtherDisk disketteLoading Drivers in Non-NetWare Environments Ndis DriversUsing Transcend PC Link SmartAgent Software Additional DriversDesktop Management Interface Performing Troubleshooting Diagnostic Tests Troubleshooting OverviewTroubleshooting with the Diagnostic Tests Starting the Diagnostic Program Starting the Diagnostic ProgramRunning the Group 1 Tests Running the Group 2 Test Assembling a Loopback PlugSetting Up an Echo Server Running the Group 3 TestStart the diagnostic program on the echo server Getting Help If a Test Fails If this test fails, try another loopback plug Changing the Test Setup To change the test parameters, follow these stepsMiscellaneous Checks Link Beat LEDSpecifications Adapter SpeciﬁcationsRJ-45 Connector Pin Assignments AUI Connector Pin AssignmentsRG59 B/U 50 ohm Cable RequirementsFor unshielded twisted-pair UTP connections 100 ohm On-line Technical Services 3Com Bulletin Board ServiceAccess by Modem Technical Support3ComFacts Automated Fax Service World Wide Web SiteThreeComForum on CompuServe To use ThreeComForum Log on to CompuServeSupport from Your Network Supplier Local numbers are available within the following countriesReturning Products for Repair To obtain an RMA number, call or faxGlossary AUI cableBackbone BackplaneBus Echo serverEMM386 EthernetTwisted-pair Numerics SymbolsIndex Eisa ﬁber-optic Windows 3.X 4-3 Windows 95 1-2, 3-3 Limited Warranty Santa Clara, CA 95052-8145 408 Interference Handbook CE Notice