Toshiba RKP004Z Copy to LCD, Operation by a copy function, Display of copy loading（fixed screen）

Page 29

8. Operation by a copy function

8. 1 Copy to LCD

Push the F3 key on an initial screen and the copy mode screen is displayed. It is not possible to drive with the [RUN] key in the following 3～5 screen display.

1 Select the memory saving group using the control dial.

2 Select copy direction [Copy to the LCD memory] using the control dial.

3 Display of copy waiting

Copy starts when the [F4] key is input.

4 Display of copy loading（fixed screen）

Copy finishes in 1 minute. When the copy is not completed even if it waits 2 minutes or more, please reset a power supply and copy again.

Note) The status display（）doesn't rotate when copying it while driving until the copy is completed.

5 Display of copy finish

Return to the copy direction window as above “2” when press the ESC key after copy.

Copy Mode

Group selection

Memory - A

Memory - B

TopInfo

Copy Mode

Memory - A

Copy direction

［Copy to the inverter］［Copy to the LCD memory］

Top

Copy Mode

Memory - A

［Copy to the LCD memory］

Waiting

Please push F4 key when starting

TopStart

F4

Copy Mode

Memory - A

［Copy to the LCD memory］

Loading

No w loadin g .

Please wa it f or about 1 min .

Copy Mode

Memory - A

［Copy to the LCD memory］

Finish

Copy was completed normally. Please push ESC-key.

CRC code：6AE3

Top

8-2

Image 29

Contents LCD Remote Keypad „ Check product purchase Introduction„ Explanation of model code Model number Introduction „ Optional products„ Limitation of use Safetyprecautionsprecautions Explanation of markings„ Transportation and installation Safety precautions „ Handling in general„ Notes on operations Safety precautions „ Operations„ Disposal Contents Names. Namesand functionsand functions „ LCD panel Names and functionsNames and functions „ About the change of parameter settings Installing the remote keypad to the inverter Installing the LCD remote keypad Installing the remote keypad to the board optionalRemote keypad Remote control optionalInverter unit インバータ⇒パネル Language Selection window appears on the screenParameter Setup Mode Top View ModeStatus Monitor Mode 54. .標About準モニタモードavailable modesSetting a panel operation frequency Operation. in Top View Modein Top View Mode„ Explanation of the top window Functions of function keys„ To change the frequency during operation Using an Easy key functionAlways Quick mode parameter PSEL=2 Operation in Top View ModeOperation Panel and Remote When used with a VF-AS1 inverter Operation Panel and Remote When used with a VF-PS1 inverterSelecting a language to be displayed Operation in Top View Mode Peak/Minimum Hold settingPress the F2 Lng key Select/confirm the desired language with the control dialPress the F4 key to carry out jog run Performing jog run60.0 Hz Emergency stop/reset operation„ When Quick mode is selected Operation. in Parameter inSetupParameterModeSetup ModeSelect/confirm History function using the control dial „ In this window, settings can be changedSelect/confirm Basic parameters using the control dial Setting a basic parameterOperation in Parameter Setup Mode Change the parameter setting Setting an extended parameterSelect/confirm Extended parameters using the control dial ［CMOd］ Select/confirm Changed Parameters using the control dialItems displayed Description Display Operation. in Status Monintor modeStatus Monitor ModeDisplaying details of an item monitored VFAS1 VFPS1 Operation. Operationby copy functionin a copy functionOperation by a copy function Copy to LCDDisplay of copy loading（fixed screen） Display of copy finish［Copy to the inverter］ Copy to inverterConfirm a memory information Function Reference WarrantyList of function key functionsFunction Key Display Position „ Outside dimensions unit mm 710. 状態. モSpecificationsニタモードでの操作Specifications Problems Possible causes Remedies Before. Beforemaking a servicemakingcall a service callBefore making a service call Warranty. Warranty