Toshiba RKP004Z Safety precautions „ Handling in general, „ Transportation and installation

Page 5

Safety precautions

„Handling in general

Warning

 

● Never disassemble, modify or repair the product.

Never

Disassembling the product may cause electric shocks, fire or injuries.

For repairs, call your sales/repair agency.

Disassem

ble

 

 

● Do not put or insert foreign objects such as waste cable, bars, or wires into the

 

product.

 

It may lead to electric shocks or fire.

Prohibited

● Do not splash water over the product, and do not wipe the body with a wet cloth.

 

It may lead to electric shocks or fire.

Turn off input power before wiring.

Wait at least 15 minutes and check to make sure that the charge lamp (on the inverter unit) is no longer lit.

Turn off the power immediately in case of any abnormalities such as smoke,

Mandatory smell or abnormal noise.

Neglect of these conditions may lead to fire. For repairs, call your sales/repair agency.

„Transportation and installation

Warning

 

● Do not install or operate the inverter if it is damaged or any part of it is missing.

 

Operating a defective inverter may lead to electric shocks or fire.

 

For repairs, call your sales/repair agency.

Prohibited

● Do not put any flammable material near the product.

It may catch fire due to the product sparking in the case of a malfunction.

 

 

●Electrical construction work must be done by a qualified expert.

 

Connection of input power by someone who does not have expert knowledge

 

may result in fire or electric shock.

 

●Operate under the environmental conditions prescribed in the instruction

 

manual.

 

Operations under any other conditions may result in malfunction.

Mandatory

●An emergency stop device must be installed that fits with system specifications

(e.g. shut off input power then engage mechanical brake).

 

Operation cannot be stopped immediately by the inverter or Remote Keypad

 

alone, thus risking an accident or injury.

 

●Use the Toshiba-specified cable for connecting this optional unit. (Refer to page

 

.)

 

The use of any other option may result in an accident.

 

Caution

Prohibited

●Do not install the product in any place subject to vibrations or it may fall. This may lead to the product falling and causing injury.

Image 5
Contents LCD Remote Keypad „ Check product purchase Introduction„ Explanation of model code Model number Introduction „ Optional products„ Limitation of use Safetyprecautionsprecautions Explanation of markings„ Transportation and installation Safety precautions „ Handling in general„ Notes on operations Safety precautions „ Operations„ Disposal Contents Names. Namesand functionsand functions „ LCD panel Names and functionsNames and functions „ About the change of parameter settings Installing the remote keypad to the inverter Installing the LCD remote keypad Installing the remote keypad to the board optionalRemote keypad Remote control optionalInverter unit インバータ⇒パネル Language Selection window appears on the screenParameter Setup Mode Top View ModeStatus Monitor Mode 54. .標About準モニタモードavailable modesSetting a panel operation frequency Operation. in Top View Modein Top View Mode„ Explanation of the top window Functions of function keys„ To change the frequency during operation Using an Easy key functionAlways Quick mode parameter PSEL=2 Operation in Top View ModeOperation Panel and Remote When used with a VF-AS1 inverter Operation Panel and Remote When used with a VF-PS1 inverterSelecting a language to be displayed Operation in Top View Mode Peak/Minimum Hold settingPress the F2 Lng key Select/confirm the desired language with the control dialPress the F4 key to carry out jog run Performing jog run60.0 Hz Emergency stop/reset operation„ When Quick mode is selected Operation. in Parameter inSetupParameterModeSetup ModeSelect/confirm History function using the control dial „ In this window, settings can be changedSelect/confirm Basic parameters using the control dial Setting a basic parameterOperation in Parameter Setup Mode Change the parameter setting Setting an extended parameterSelect/confirm Extended parameters using the control dial [CMOd] Select/confirm Changed Parameters using the control dialItems displayed Description Display Operation. in Status Monintor modeStatus Monitor ModeDisplaying details of an item monitored VFAS1 VFPS1 Operation. Operationby copy functionin a copy functionOperation by a copy function Copy to LCDDisplay of copy loading(fixed screen) Display of copy finish[Copy to the inverter] Copy to inverterConfirm a memory information Function Reference WarrantyList of function key functionsFunction Key Display Position „ Outside dimensions unit mm 710. 状態. モSpecificationsニタモードでの操作Specifications Problems Possible causes Remedies Before. Beforemaking a servicemakingcall a service callBefore making a service call Warranty. Warranty