Toshiba B-SA4T installation manual Close the Strip Unit, System Mode Manual

Page 11

INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT

EO15-33001A

2. Strip Module

5.Secure the Strip Unit to the printer with the two screws. Make sure that the Feed Roller Gear rotates smoothly.

Strip Unit

Feed Roller Gear

SMW-3x6 Screw

6. Close the Strip Unit.

Strip Unit

7.Connect the Strip Harness to the connector at the front of the printer. At this time, carefully avoid contact of the strip harness with the gears.

Gear

Strip Harness

8.Close the Strip Module Cover.

Perform an operation check for a proper strip issue.

• Media loading procedure-------------	Owner’s Manual, Section 2.3
• Operation check------------------------	Owner’s Manual, Section 2.9
• System mode setting------------------	System Mode Manual
• Cleaning ---------------------------------	Owner’s Manual, Section 4.1.4
	2- 3

Connector

Strip Harness

Image 11

Contents SA4T Series Table of Contents SA204-QM / B-SA204-QM-R Cutter Module100 Front Cover Hinge Screw Close the Cutter Module Cover System Mode ManualSA204P-QM-R Open the Front Cover, and remove the Connector CoverSet Screw Cutter Unit Connector 3x6 Screw Ground Wire Cutter Harness SA904-H-QM-R Guide Roller 1 pc Installation Manual 1 copyStrip Module 100 Front Cover HingeScrew Close the Strip Unit Attaching the Cutter System Mode Settings for Stripping PET Labels 3ADJUST SET Feed ADJ 2PARAMETER SET Back Speed STD SMW-3x6 Screw 4 pcs SA904P-H-QM-R100 Front Cover HingeStopper Close the Strip Unit Opening Strip Unit Cutter FCC/IC Sticker 1 pc Wireless LAN Module B-SA704-WLAN-QMSA4TM SA4TP Remove the two SMW-3x6 screws from the back of the printerRemove the SMW-3x8 screw to detach the Cable Clamp Remove the two SMW-3x6 screws to detach the Blind PlateCopper foil Re-attach the Side Panel to the printer Country Code Remove the two screws from the back of the printer Serial Interface Board B-SA704-RS-QM-RSMW-3x6 Screw 3 pcs Remove the two screws to detach the Blind Plate Fit the Locking Support into the Main PC Board SMW-3x6 Locking Support Never loosen or remove these screws Dpi Print Head Kit B-SA704-TPH3-QM-RPacking List Disconnect the Print Head Cable from the Print Head Installation ProcedureReal Time Clock B-SA704-RTC-QM-R Battery Socket Lithium Battery Battery Sticker Care must be taken not to catch Connect the Interface Cable to CN501 on the Main PC BoardSet the date and time using the following procedure System Setting Date and Time SettingWith the Feed or Restart key Expansion I/O Board B-SA704-IO-QM-R SMW-3x6 Screw Blind Plate Attach the Side Panel, removed in , back to the printer Connect the Interface Cable to CN4 on the Main PC BoardApplicable Model Rfid Module B-SA704-RFID-U2-EU-RPacking List Outline of the introduction of an Rfid Kit Side Panel Hook Upper Sensor Ass’y Upper Sensor Lever Connect the Interface Cable to CN6 on the Main PC Board. CN6 Attach the Cable Clamp to the position shown below Connect the Interface Cable to the Rfid Module Re-place the Media Sensor Block When Short-Pitch Rfid Tags 20mm are usedMedia Guide Module None Rfid Module SettingsEPC C1 Gen2 Cycle TIM ADJ Retry +00 Value AGC Threshold Setting From the previous 3132333435363738 39304142 0A 0500-02 08 5 D Service No. LabelIdentification of The Rfid Module B-SA704-RFID-U2-EU-R Serial No. Label