Toshiba B-SA4T installation manual Rfid Module Settings, Module None

Page 51

INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT

EO15-33001A

(Revision Date: Feb. 25, 2008)

8. RFID Module: B-SA704-RFID-U2-EU-R

•RFID Module Settings

After installing the RFID Module on the printer, configure the RFID module settings using the system mode on the printer.

Turn on the printer while holding down the [FEED] and [PAUSE] keys at the same time.

<1>DIAG. V1.6

[RESTART]

When “<1>DIAG. V1.6“ appears on the LCD, press the [RESTART] key.

<10>RFID

[PAUSE]

RFID setting menu ”<10>RFID” is displayed. Press the [PAUSE] key.

<10>RFID

READ TEST OFF

[PAUSE]

<10>RFID

CAREERSENSE OFF

[PAUSE]

<10>RFID

MODULE NONE

[PAUSE]

Continued to the next

page.

Read test menu is displayed. Choose whether to perform a read test or not with the [RESTART] or [FEED] key.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[RESTART]

READ TEST OFF

 

 

 

 

 

 

READ TEST ON

 

 

 

[FEED]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF:

 

A read test is not performed. (Initially, choose “OFF”.)

ON:

 

A read test is performed.

 

 

The printer enters the read test mode, and a read test is performed each time the

 

 

[PAUSE] key is pressed. When the data of a tag can be read, it is displayed on the

 

 

LCD.

 

•Read data is displayed in hex. value on the 16-digit x 2-line LCD.

1234567890123456

6543210987654321

When the RFID tag contains 16 digits or more data, the first 16 digits are displayed. When data volume is less than 16 digits, the vacant digits will be filled with spaces.

•If the tag cannot be read, “RFID TIMEOUT” or “RFID READ ERROR” is displayed.

•If the type of the tag to be read and one selected by the RFID tag type selection do not match, an RFID tag read error will result.

Make sure the RFID tag type has been selected before the read test is started.

After choosing an option, press the [PAUSE] key.

Carrier sense setting menu is displayed. This menu is not available to the B-SA704-RFID- U2-EU-R. Press the [PAUSE] key to skip this menu.

Module type setting menu is displayed. Choose “U2” with the [FEED] or [RESTART] key.

U1: Not available. [RESTART] H1: not available.

NONE: No RFID Module is installed.

[FEED] U2: B-SA704-RFID-U2-EU-R

H2: Not available.

Press the [PAUSE] key.

8- 11

Page 50 Page 52
Image 51
Page 50 Page 52
Contents SA4T Series Table of Contents SA204-QM / B-SA204-QM-R Cutter Module100 Front Cover Hinge Screw Close the Cutter Module Cover System Mode ManualSA204P-QM-R Open the Front Cover, and remove the Connector CoverSet Screw Cutter Unit Connector 3x6 Screw Ground Wire Cutter Harness Guide Roller 1 pc Installation Manual 1 copy Strip ModuleSA904-H-QM-R 100 Front Cover HingeScrew Close the Strip Unit Attaching the Cutter System Mode Settings for Stripping PET Labels 3ADJUST SET Feed ADJ 2PARAMETER SET Back Speed STD SMW-3x6 Screw 4 pcs SA904P-H-QM-R100 Front Cover HingeStopper Close the Strip Unit Opening Strip Unit Cutter FCC/IC Sticker 1 pc Wireless LAN Module B-SA704-WLAN-QMSA4TM SA4TP Remove the two SMW-3x6 screws from the back of the printerRemove the SMW-3x8 screw to detach the Cable Clamp Remove the two SMW-3x6 screws to detach the Blind PlateCopper foil Re-attach the Side Panel to the printer Country Code Serial Interface Board B-SA704-RS-QM-R SMW-3x6 Screw 3 pcsRemove the two screws from the back of the printer Remove the two screws to detach the Blind Plate Fit the Locking Support into the Main PC Board SMW-3x6 Locking Support Dpi Print Head Kit B-SA704-TPH3-QM-R Packing ListNever loosen or remove these screws Disconnect the Print Head Cable from the Print Head Installation ProcedureReal Time Clock B-SA704-RTC-QM-R Battery Socket Lithium Battery Battery Sticker Care must be taken not to catch Connect the Interface Cable to CN501 on the Main PC BoardSet the date and time using the following procedure System Setting Date and Time SettingWith the Feed or Restart key Expansion I/O Board B-SA704-IO-QM-R SMW-3x6 Screw Blind Plate Attach the Side Panel, removed in , back to the printer Connect the Interface Cable to CN4 on the Main PC BoardApplicable Model Rfid Module B-SA704-RFID-U2-EU-RPacking List Outline of the introduction of an Rfid Kit Side Panel Hook Upper Sensor Ass’y Upper Sensor Lever Connect the Interface Cable to CN6 on the Main PC Board. CN6 Attach the Cable Clamp to the position shown below Connect the Interface Cable to the Rfid Module Re-place the Media Sensor Block When Short-Pitch Rfid Tags 20mm are usedMedia Guide Module None Rfid Module SettingsEPC C1 Gen2 Cycle TIM ADJ Retry +00 Value AGC Threshold Setting From the previous 3132333435363738 39304142 0A 0500-02 08 5 D Service No. LabelIdentification of The Rfid Module B-SA704-RFID-U2-EU-R Serial No. Label
Top Page Image Contents