Toshiba B-SA4T installation manual Media Guide

Page 50

Media Guide

Shield Sheet Media Guide

Shield Sheet

INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT

EO15-33001A

(Revision Date: Feb. 25, 2008)

8. RFID Module: B-SA704-RFID-U2-EU-R

2.Insert the Shield Sheet, without the backing paper removed, under the Media Guides from behind, and slightly slide it toward the Platen. Then, move the Media Guides to the width of the Shield Sheet (shorter width), as the pictures show. The purpose of this is to indicate the center of the attachment

position. Platen

Media Guide

3.Remove the backing paper from the Shield Sheet, and attach it to the position determined in the previous step, as indicated in the picture below. Now, the Shield Sheet attachment is completed. Next, refer to Section 5 and configure the RFID module settings.

Media Guide Block

Shield Sheet

8- 10

Image 50

Contents SA4T Series Table of Contents Cutter Module SA204-QM / B-SA204-QM-R100 Front Cover Hinge Screw System Mode Manual Close the Cutter Module CoverOpen the Front Cover, and remove the Connector Cover SA204P-QM-RSet Screw Cutter Unit Connector 3x6 Screw Ground Wire Cutter Harness SA904-H-QM-R Guide Roller 1 pc Installation Manual 1 copyStrip Module 100 Front Cover HingeScrew Close the Strip Unit Attaching the Cutter System Mode Settings for Stripping PET Labels 3ADJUST SET Feed ADJ 2PARAMETER SET Back Speed STD SA904P-H-QM-R SMW-3x6 Screw 4 pcs100 Front Cover HingeStopper Close the Strip Unit Opening Strip Unit Cutter Wireless LAN Module B-SA704-WLAN-QM FCC/IC Sticker 1 pcRemove the two SMW-3x6 screws from the back of the printer SA4TM SA4TPRemove the two SMW-3x6 screws to detach the Blind Plate Remove the SMW-3x8 screw to detach the Cable ClampCopper foil Re-attach the Side Panel to the printer Country Code Remove the two screws from the back of the printer Serial Interface Board B-SA704-RS-QM-RSMW-3x6 Screw 3 pcs Remove the two screws to detach the Blind Plate Fit the Locking Support into the Main PC Board SMW-3x6 Locking Support Never loosen or remove these screws Dpi Print Head Kit B-SA704-TPH3-QM-RPacking List Installation Procedure Disconnect the Print Head Cable from the Print HeadReal Time Clock B-SA704-RTC-QM-R Battery Socket Lithium Battery Battery Sticker Connect the Interface Cable to CN501 on the Main PC Board Care must be taken not to catchSystem Setting Date and Time Setting Set the date and time using the following procedureWith the Feed or Restart key Expansion I/O Board B-SA704-IO-QM-R SMW-3x6 Screw Blind Plate Connect the Interface Cable to CN4 on the Main PC Board Attach the Side Panel, removed in , back to the printerRfid Module B-SA704-RFID-U2-EU-R Applicable ModelPacking List Outline of the introduction of an Rfid Kit Side Panel Hook Upper Sensor Ass’y Upper Sensor Lever Connect the Interface Cable to CN6 on the Main PC Board. CN6 Attach the Cable Clamp to the position shown below Connect the Interface Cable to the Rfid Module When Short-Pitch Rfid Tags 20mm are used Re-place the Media Sensor BlockMedia Guide Rfid Module Settings Module NoneEPC C1 Gen2 Cycle TIM ADJ Retry +00 Value AGC Threshold Setting From the previous 3132333435363738 39304142 0A Serial No. Label Service No. LabelIdentification of The Rfid Module B-SA704-RFID-U2-EU-R 0500-02 08 5 D