Toshiba B-SA4T installation manual SA904P-H-QM-R, SMW-3x6 Screw 4 pcs

Page 16

INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT

EO15-33001A

(Revision Date: Jan: 19, 2006)

2. Strip Module

2.2 B-SA904P-H-QM-R

B-SA904P-H-QM-R is an optional strip module for the B-SA4TP Series (Plastic cover).

•Packing List

Strip Unit (1 pc.)

Strip Module Cover (1 pc.)

SMW-3x6 Screw (4 pcs.)

Cutter (1 pc.)

Guide Roller (1 pc.)

Installation Manual (1 copy)

NOTE: When issuing labels in batch mode even though the strip module is fitted, please use the provided cutter to tear off the issued labels. Do not attach the cutter when labels are stripped one by one.

•Installation Procedure

1. Open the Top Cover and the Front Cover. Remove the Connector Cover.

Top Cover

Connector Cover

Front Cover

B-3x6 Screw

2- 8

Image 16

Contents SA4T Series Table of Contents Cutter Module SA204-QM / B-SA204-QM-R100 Front Cover Hinge Screw System Mode Manual Close the Cutter Module CoverOpen the Front Cover, and remove the Connector Cover SA204P-QM-RSet Screw Cutter Unit Connector 3x6 Screw Ground Wire Cutter Harness Strip Module Guide Roller 1 pc Installation Manual 1 copySA904-H-QM-R 100 Front Cover HingeScrew Close the Strip Unit Attaching the Cutter System Mode Settings for Stripping PET Labels 3ADJUST SET Feed ADJ 2PARAMETER SET Back Speed STD SA904P-H-QM-R SMW-3x6 Screw 4 pcs100 Front Cover HingeStopper Close the Strip Unit Opening Strip Unit Cutter Wireless LAN Module B-SA704-WLAN-QM FCC/IC Sticker 1 pcRemove the two SMW-3x6 screws from the back of the printer SA4TM SA4TPRemove the two SMW-3x6 screws to detach the Blind Plate Remove the SMW-3x8 screw to detach the Cable ClampCopper foil Re-attach the Side Panel to the printer Country Code SMW-3x6 Screw 3 pcs Serial Interface Board B-SA704-RS-QM-RRemove the two screws from the back of the printer Remove the two screws to detach the Blind Plate Fit the Locking Support into the Main PC Board SMW-3x6 Locking Support Packing List Dpi Print Head Kit B-SA704-TPH3-QM-RNever loosen or remove these screws Installation Procedure Disconnect the Print Head Cable from the Print HeadReal Time Clock B-SA704-RTC-QM-R Battery Socket Lithium Battery Battery Sticker Connect the Interface Cable to CN501 on the Main PC Board Care must be taken not to catchSystem Setting Date and Time Setting Set the date and time using the following procedureWith the Feed or Restart key Expansion I/O Board B-SA704-IO-QM-R SMW-3x6 Screw Blind Plate Connect the Interface Cable to CN4 on the Main PC Board Attach the Side Panel, removed in , back to the printerRfid Module B-SA704-RFID-U2-EU-R Applicable ModelPacking List Outline of the introduction of an Rfid Kit Side Panel Hook Upper Sensor Ass’y Upper Sensor Lever Connect the Interface Cable to CN6 on the Main PC Board. CN6 Attach the Cable Clamp to the position shown below Connect the Interface Cable to the Rfid Module When Short-Pitch Rfid Tags 20mm are used Re-place the Media Sensor BlockMedia Guide Rfid Module Settings Module NoneEPC C1 Gen2 Cycle TIM ADJ Retry +00 Value AGC Threshold Setting From the previous 3132333435363738 39304142 0A Service No. Label Identification of The Rfid Module B-SA704-RFID-U2-EU-RSerial No. Label 0500-02 08 5 D