Toshiba B-SA4T installation manual Connect the Interface Cable to CN501 on the Main PC Board

Page 35

INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT

EO15-33001A

(Revision Date: Jan. 19, 2006)

6. Real Time Clock: B-SA704-RTC-QM-R

5.Pass the Interface Cable through the Cable Clamp, and between CN1 and CN2 on the MAIN PC Board, as shown in the pictures below. For the B-SA4TP model, wind the cable on the two Cable Clamps.

	B-SA4TP Model		Connector CN2

	MAIN PC Board

Interface Cable

B-SA4TM Model	Connector CN1	Cable Clamp	Interface Cable
B-SA4TM Model	Connector CN2
	Connector CN2

MAIN PC Board

Interface Cable

Connector CN1

Cable Clamp

Interface Cable

6.Connect the Interface Cable to CN501 on the MAIN PC Board.

CN501

Interface Cable

7.Attach the Side Panel, removed in Step 2, back to the printer. Interface Cable by the Side Panel.

MAIN PC Board

Care must be taken not to catch the

NOTE: When the B-SA704-IO-QM-R Expansion I/O Board or B-SA704-RS-QM-R Serial Interface Board was removed beforehand, re-install it.

6- 4

Image 35

Contents SA4T Series Table of Contents SA204-QM / B-SA204-QM-R Cutter Module100 Front Cover Hinge Screw Close the Cutter Module Cover System Mode ManualSA204P-QM-R Open the Front Cover, and remove the Connector CoverSet Screw Cutter Unit Connector 3x6 Screw Ground Wire Cutter Harness SA904-H-QM-R Guide Roller 1 pc Installation Manual 1 copyStrip Module 100 Front Cover HingeScrew Close the Strip Unit Attaching the Cutter System Mode Settings for Stripping PET Labels 3ADJUST SET Feed ADJ 2PARAMETER SET Back Speed STD SMW-3x6 Screw 4 pcs SA904P-H-QM-R100 Front Cover HingeStopper Close the Strip Unit Opening Strip Unit Cutter FCC/IC Sticker 1 pc Wireless LAN Module B-SA704-WLAN-QMSA4TM SA4TP Remove the two SMW-3x6 screws from the back of the printerRemove the SMW-3x8 screw to detach the Cable Clamp Remove the two SMW-3x6 screws to detach the Blind PlateCopper foil Re-attach the Side Panel to the printer Country Code Remove the two screws from the back of the printer Serial Interface Board B-SA704-RS-QM-RSMW-3x6 Screw 3 pcs Remove the two screws to detach the Blind Plate Fit the Locking Support into the Main PC Board SMW-3x6 Locking Support Never loosen or remove these screws Dpi Print Head Kit B-SA704-TPH3-QM-RPacking List Disconnect the Print Head Cable from the Print Head Installation ProcedureReal Time Clock B-SA704-RTC-QM-R Battery Socket Lithium Battery Battery Sticker Care must be taken not to catch Connect the Interface Cable to CN501 on the Main PC BoardSet the date and time using the following procedure System Setting Date and Time SettingWith the Feed or Restart key Expansion I/O Board B-SA704-IO-QM-R SMW-3x6 Screw Blind Plate Attach the Side Panel, removed in , back to the printer Connect the Interface Cable to CN4 on the Main PC BoardApplicable Model Rfid Module B-SA704-RFID-U2-EU-RPacking List Outline of the introduction of an Rfid Kit Side Panel Hook Upper Sensor Ass’y Upper Sensor Lever Connect the Interface Cable to CN6 on the Main PC Board. CN6 Attach the Cable Clamp to the position shown below Connect the Interface Cable to the Rfid Module Re-place the Media Sensor Block When Short-Pitch Rfid Tags 20mm are usedMedia Guide Module None Rfid Module SettingsEPC C1 Gen2 Cycle TIM ADJ Retry +00 Value AGC Threshold Setting From the previous 3132333435363738 39304142 0A 0500-02 08 5 D Service No. LabelIdentification of The Rfid Module B-SA704-RFID-U2-EU-R Serial No. Label