Toshiba B-SA4T installation manual Rfid Module B-SA704-RFID-U2-EU-R, Applicable Model

Page 41

INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT

EO15-33001A

(Revision Date: Feb. 14, 2008)

8. RFID Module: B-SA704-RFID-U2-EU-R

8. RFID Module: B-SA704-RFID-U2-EU-R

This optional device is intended for adding the RFID tag read/write function to the B-SA4TM and B-SA4TP series.

WARNING!

1.Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution.

•Manual instructions must be followed when installing option kits or adding cables to avoid system failures and to insure proper performance and operation.

•Failure to follow manual instructions or any unauthorized modifications, substitution or change to this product will void the limited product warranty.

2.Turn the power OFF and disconnect the power cord before installing the RFID module.

3.Be careful not to pinch your fingers or hands with the covers.

4.The print head and stepping motor becomes very hot immediately after printing. Do not touch the print head, stepping motor and around it right after printing, or you may get burned.

5.When opening the top cover, it must be fully opened. Failure to do this may cause the top cover to close under its own weight, resulting in an injury.

CAUTION!

Be careful not to damage the pattern of the Antenna Ass’y or peel off the Shield Sheet. Damaged pattern or removed Sheild Sheet may affect the ability to read or write RFID tags.

Antenna Ass’y

Pattern

Shield Sheet

 

•Applicable Model

This optional device is intended for the following models:

Notes: 1. To use this device firmware V1.6 or greater is required. Upgrade the firmware to V1.6 or greater, if necessary. For the downloading procedure, refer to the B-SA4T Series System Mode Manual.

2. The countries where the use of this device is allowed are as follows:

Model Name

Frequency Band

Applicable Countries

 

UHF 869.7 to

Austria, Belgium, Cyprus, Czech, Denmark, Estonia, Germany,

B-SA704-RFID–U2-EU-R

870.0MHz (Center

Greece, Finland, France, Hungary, Ireland, Italy, Latvia,

frequency:

Lithuania, Luxemburg, Malta, Poland, Portugal, Slovakia,

 

 

869.85MHz)

Slovenia, Spain, Sweden, the Netherlands, and U.K.

8- 1

Page 40 Page 42
Image 41
Page 40 Page 42
Contents SA4T Series Table of Contents SA204-QM / B-SA204-QM-R Cutter Module100 Front Cover Hinge Screw Close the Cutter Module Cover System Mode ManualSA204P-QM-R Open the Front Cover, and remove the Connector CoverSet Screw Cutter Unit Connector 3x6 Screw Ground Wire Cutter Harness SA904-H-QM-R Guide Roller 1 pc Installation Manual 1 copyStrip Module 100 Front Cover HingeScrew Close the Strip Unit Attaching the Cutter System Mode Settings for Stripping PET Labels 3ADJUST SET Feed ADJ 2PARAMETER SET Back Speed STD SMW-3x6 Screw 4 pcs SA904P-H-QM-R100 Front Cover HingeStopper Close the Strip Unit Opening Strip Unit Cutter FCC/IC Sticker 1 pc Wireless LAN Module B-SA704-WLAN-QMSA4TM SA4TP Remove the two SMW-3x6 screws from the back of the printerRemove the SMW-3x8 screw to detach the Cable Clamp Remove the two SMW-3x6 screws to detach the Blind PlateCopper foil Re-attach the Side Panel to the printer Country Code Remove the two screws from the back of the printer Serial Interface Board B-SA704-RS-QM-RSMW-3x6 Screw 3 pcs Remove the two screws to detach the Blind Plate Fit the Locking Support into the Main PC Board SMW-3x6 Locking Support Never loosen or remove these screws Dpi Print Head Kit B-SA704-TPH3-QM-RPacking List Disconnect the Print Head Cable from the Print Head Installation ProcedureReal Time Clock B-SA704-RTC-QM-R Battery Socket Lithium Battery Battery Sticker Care must be taken not to catch Connect the Interface Cable to CN501 on the Main PC BoardSet the date and time using the following procedure System Setting Date and Time SettingWith the Feed or Restart key Expansion I/O Board B-SA704-IO-QM-R SMW-3x6 Screw Blind Plate Attach the Side Panel, removed in , back to the printer Connect the Interface Cable to CN4 on the Main PC BoardApplicable Model Rfid Module B-SA704-RFID-U2-EU-RPacking List Outline of the introduction of an Rfid Kit Side Panel Hook Upper Sensor Ass’y Upper Sensor Lever Connect the Interface Cable to CN6 on the Main PC Board. CN6 Attach the Cable Clamp to the position shown below Connect the Interface Cable to the Rfid Module Re-place the Media Sensor Block When Short-Pitch Rfid Tags 20mm are usedMedia Guide Module None Rfid Module SettingsEPC C1 Gen2 Cycle TIM ADJ Retry +00 Value AGC Threshold Setting From the previous 3132333435363738 39304142 0A Identification of The Rfid Module B-SA704-RFID-U2-EU-R Service No. LabelSerial No. Label 0500-02 08 5 D
Top Page Image Contents