Toshiba B-SA4T installation manual 3ADJUST SET Feed ADJ

Page 14

INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT

EO15-33001A

(Revision Date: Jan. 19, 2006)

2. Strip Module

9.Turn off the printer, and then back to on. Send an issue command to the printer for strip issue.

10.If necessary, fine adjust the print start position and strip position in the system mode.

NOTES:

1.It is recommended that the print start position and strip position are adjusted on the actual print condition.

2.When short-pitch labels are used, the print start position may misalign on the first few labels. In that case, feed the labels between the media sensor and the strip shaft, and discard them.

Label	Media Sensor

Strip Shaft

Discard labels between the media sensor and the strip shaft.

11.Repeat Steps 9 and 10 for position fine adjustment.

12.After the print position and strip position are properly adjusted, access “<2>PARAMETER SET” menu in the system mode again.

(Continued.)
Turn the power OFF.
Turn the power ON.
Issue labels.
Print position		Good
Print position
Adjustment
is required.
Power OFF
Power ON
	FEED	RESTART
<1>DIAG.
V1.1
Print position fine adjustment
<3>ADJUST SET
FEED ADJ.	+0.0mm
Strip position fine adjustment
<3>ADJUST SET
CUT ADJ.	+0.0mm
Turn the power OFF.
Turn the power ON.
	FEED	RESTART
<1>DIAG.
V1.1

FEED

<2>PARAMETER SET

Continued.

2- 6

Image 14

Contents SA4T Series Table of Contents Cutter Module SA204-QM / B-SA204-QM-R100 Front Cover Hinge Screw System Mode Manual Close the Cutter Module CoverOpen the Front Cover, and remove the Connector Cover SA204P-QM-RSet Screw Cutter Unit Connector 3x6 Screw Ground Wire Cutter Harness SA904-H-QM-R Guide Roller 1 pc Installation Manual 1 copyStrip Module 100 Front Cover HingeScrew Close the Strip Unit Attaching the Cutter System Mode Settings for Stripping PET Labels 3ADJUST SET Feed ADJ 2PARAMETER SET Back Speed STD SA904P-H-QM-R SMW-3x6 Screw 4 pcs100 Front Cover HingeStopper Close the Strip Unit Opening Strip Unit Cutter Wireless LAN Module B-SA704-WLAN-QM FCC/IC Sticker 1 pcRemove the two SMW-3x6 screws from the back of the printer SA4TM SA4TPRemove the two SMW-3x6 screws to detach the Blind Plate Remove the SMW-3x8 screw to detach the Cable ClampCopper foil Re-attach the Side Panel to the printer Country Code Remove the two screws from the back of the printer Serial Interface Board B-SA704-RS-QM-RSMW-3x6 Screw 3 pcs Remove the two screws to detach the Blind Plate Fit the Locking Support into the Main PC Board SMW-3x6 Locking Support Never loosen or remove these screws Dpi Print Head Kit B-SA704-TPH3-QM-RPacking List Installation Procedure Disconnect the Print Head Cable from the Print HeadReal Time Clock B-SA704-RTC-QM-R Battery Socket Lithium Battery Battery Sticker Connect the Interface Cable to CN501 on the Main PC Board Care must be taken not to catchSystem Setting Date and Time Setting Set the date and time using the following procedureWith the Feed or Restart key Expansion I/O Board B-SA704-IO-QM-R SMW-3x6 Screw Blind Plate Connect the Interface Cable to CN4 on the Main PC Board Attach the Side Panel, removed in , back to the printerRfid Module B-SA704-RFID-U2-EU-R Applicable ModelPacking List Outline of the introduction of an Rfid Kit Side Panel Hook Upper Sensor Ass’y Upper Sensor Lever Connect the Interface Cable to CN6 on the Main PC Board. CN6 Attach the Cable Clamp to the position shown below Connect the Interface Cable to the Rfid Module When Short-Pitch Rfid Tags 20mm are used Re-place the Media Sensor BlockMedia Guide Rfid Module Settings Module NoneEPC C1 Gen2 Cycle TIM ADJ Retry +00 Value AGC Threshold Setting From the previous 3132333435363738 39304142 0A Serial No. Label Service No. LabelIdentification of The Rfid Module B-SA704-RFID-U2-EU-R 0500-02 08 5 D