Siemens MCC-3298 user manual Rva

Page 18

3 Operating the SAMMS-LV Device

						Input Assignments

	Starter	Program	Control Type	PB1	PB2	PB3	PB4	PB5	PB6
	Type	Block

Available with	RVA	PB46	LOCAL, 2-WIRE	OFF	ON
SAMMS-LVX	(Auto TX)
SAMMS-LVX	(Auto TX)	PB47	LOCAL, 3-WIRE	STOP	START
only	Sizes 2-4	PB47	LOCAL, 3-WIRE	STOP	START

		PB48	LOCAL, 3-WIRE, REMOTE 2-WIRE	STOP	START		HAND	OFF	AUTO
		PB48	LOCAL, 3-WIRE, REMOTE 2-WIRE	STOP	START		HAND	OFF	AUTO

		PB49	LOCAL/REMOTE 2-WIRE	STOP			HAND	OFF	AUTO

		PB50	LOCAL/REMOTE 3-WIRE	STOP	START

		PB51	REMOTE, 2-WIRE

		PB52	REMOTE, 3-WIRE

	RVA	PB53	LOCAL, 2-WIRE	OFF	ON
	(Auto TX)
	(Auto TX)	PB54	LOCAL, 3-WIRE	STOP	START
	Sizes 5-6	PB54	LOCAL, 3-WIRE	STOP	START
	Sizes 5-6
		PB55	LOCAL, 3-WIRE, REMOTE 2-WIRE	STOP	START		HAND	OFF	AUTO

		PB56	LOCAL/REMOTE 2-WIRE	STOP			HAND	OFF	AUTO

		PB57	LOCAL/REMOTE 3-WIRE	STOP	START

		PB58	REMOTE, 2-WIRE

		PB59	REMOTE, 3-WIRE

	YDC	PB60	LOCAL, 2-WIRE	OFF	ON

		PB61	LOCAL, 3-WIRE	STOP	START

		PB62	LOCAL, 3-WIRE, REMOTE 2-WIRE	STOP	START		HAND	OFF	AUTO

		PB63	LOCAL/REMOTE 2-WIRE	STOP			HAND	OFF	AUTO

		PB64	LOCAL/REMOTE 3-WIRE	STOP	START

		PB65	REMOTE, 2-WIRE

		PB66	REMOTE, 3-WIRE

	YDO	PB67	LOCAL, 2-WIRE	OFF	ON

		PB68	LOCAL, 3-WIRE	STOP	START

		PB69	LOCAL, 3-WIRE, REMOTE 2-WIRE	STOP	START		HAND	OFF	AUTO

		PB70	LOCAL/REMOTE 2-WIRE	STOP			HAND	OFF	AUTO

		PB71	LOCAL/REMOTE 3-WIRE	STOP	START

		PB72	REMOTE, 2-WIRE

		PB73	REMOTE, 3-WIRE

	PW	PB74	LOCAL, 2-WIRE	OFF	ON

		PB75	LOCAL, 3-WIRE	STOP	START

		PB76	LOCAL, 3-WIRE, REMOTE 2-WIRE	STOP	START		HAND	OFF	AUTO

		PB77	LOCAL/REMOTE 2-WIRE	STOP			HAND	OFF	AUTO

		PB78	LOCAL/REMOTE 3-WIRE	STOP	START

		PB79	REMOTE, 2-WIRE

		PB80	REMOTE, 3-WIRE

Table 3.3 Standard control circuits (continued)

16

Image 18

Contents SAMMS-LV Qualified Person Contents Signal Words Field Service OperationQualified Person About this Manual SAMMS-LV Device Models Advanced Protection for Low-Voltage MotorsUsing the Standardized Control Panel Overload ProtectionProgramming Control Circuits Outputs One Change settings requires password Yes Remote inputsSAMMS-LV Model Light barsInstalling the SAMMS-LV Device Full voltage non-reversing connection diagram Grounding the Device SAMMS-LV device communications connections Performing a Lamp Test Password ProtectionUsing the Reset/Test Push Button Performing an Overload Relay TestOutput Devices Input DevicesLadder Diagrams Library of Standard Ladder Diagrams Custom Ladder DiagramsSAMMS-LVX Standard control circuits RVA Incomplete Sequence Ridethrough Upon Loss of Power SAMMS-LVX OnlyMotor Ambient Temperature Intelligent Reduced-Voltage Starting SAMMS-LVX OnlyODP motor thermal signature Operating the SAMMS-LV Operating the SAMMS-LV Device 10 Motor protection graph Dual Overload Protection SAMMS-LVX Only Ultimate Trip Level and Service FactorPhase Unbalance Jam Protection SAMMS-LVX OnlyRepetitive Starts Ground Fault DetectionStator Protection Start InhibitSize Pickup Current Default Pickup Range Autoreset After a Trip SAMMS-LVX OnlyUsing the Hand Held Communicator HHC Emergency RestartingFunction Number 5A CT primary current if used Full load current for OLR NoJam pickup current F24 Loss of load protection or warning List Key Using the Enter KeyFunction Key UP and Down KeysExternal trips Enable/disable phase unbalance CapabilityMeans warning Select ground fault pick-up current Value 2A-5AStep Size Second Default Value Iflc is the value of Iflc forSelect jam pickup current 120-400% I FLC F24 Loss of Load Using the SAMMS-LV Device Func TionsProgram Mode/Passwords 200% 50% 480013 Entering and changing passwords F1 Control Circuit Number and Incomplete Se- quence Status F0 Ambient TemperatureSAMMS-LV Functions F2 Size for Overload Relay #145A Overload Setting Step Default Relay Size Range 24.0A 36AF4 Full-Load Current for Overload Relay #1 90AF9 Phase Unbalance Protection F6 Service FactorF8 Autoreset SAMMS-LVX Only F7 Overload Trip ClassF12 Ground Fault Protection or Warning F10 Display Time to RestartF11 Emergency Restarting F14 Set Programmable Timer #2 F12A Ground Fault Pickup CurrentF13 Set Programmable Timer #1 F15 Display CurrentF18 Display Total Elapsed Run Time of the Motor F21 Reset Motor DataF17 Current Unbalance F19 Number of Motor StartsF24 Loss of Load Protection or Warning SAMMS-LVX Only F25 Percentage of Motor Winding TemperatureF23A Jam Pickup Current SAMMS-LVX Only F24A Loss of Load Pickup Current SAMMS-LVX OnlyF27 Address Troubleshooting Error Condition Troubleshooting Guide Error Condition Appendix a Technical Specifications Overload Specifications Statistical Data Dimensions Catalog Number SAM4 Switch # Function Position Samms Sensor, sizes 1C, 2A, 2B Page Siemens Energy Automation, Inc