NETGEAR JNR1010V2 Back Panel, Back panel has the following ports, button, and connector

Page 10

JNR1010v2 N150 Wireless Router

Back Panel

The back panel has the following ports, button, and connector:

WPS/Reset button

AC power connector

Ethernet ports Internet port

Figure 3. Back panel

Table 2. Back panel port, button, and connector descriptions

Port or Connector	Description

Ethernet ports	Four local area networks (LAN) 10/100 Mbps Ethernet ports for connecting
	the router to your local computers.

Internet port	Ethernet port for connecting the router to a cable broadband modem or DSL
	broadband modem. The Internet port is also referred to as the WAN port.

Hardware Setup

10

Image 10

Contents JNR1010v2 N150 Wireless Router Compliance SupportTrademarks Contents Administration Appendix a Supplemental Information Hardware Setup Get to know your routerHardware Features Unpack Your RouterFront Panel Router front panel has the following status LEDsJNR1010v2 N150 Wireless Router Front panel LED descriptions Back panel has the following ports, button, and connector Back PanelLabel Position Your Router To position your router  To prepare your router for installation Cable Your Router Verify the Cabling  To start your networkGet Started with Netgear genie Connect to the routerWireless Devices and Security Settings Router Setup PreparationTypes of Logins and Access Use Standard TCP/IP Properties for Dhcp To use Netgear genie to set up your router Netgear genie SetupBrowse to http//routerlogin.net Log In to Your Router After Installation Upgrade Router FirmwareBasic Home Screen Change the Password Select Advanced Administration Set Password To set up password recovery Password RecoverySelect the Enable Password Recovery check box  To recover your password  To use WPS to join the wireless network Add Wireless Devices or Computers to Your NetworkWi-Fi Protected Setup Method Manual MethodGenie Basic Settings Your Internet connection and network To view or change the Internet setup Internet SetupSelect Basic Internet Internet IP Address Internet IP Address Basic Wireless Settings Select Basic WirelessGenie Basic Settings Genie Basic Settings WPA-PSK and WPA-PSK + WPA2-PSK Mixed Mode Security Options To configure the WEP security and wireless passphrase WEPGenie Basic Settings  To view the devices that are connected to your networks Attached DevicesSelect Basic Attached Devices Guest Network  To set up a guest networkSelect Basic Guest Network Genie Basic Settings Specify custom settings Genie Advanced HomeSetup Wizard  To launch the Setup WizardGenie Advanced Home WPS Wizard  To use the WPS WizardGenie Advanced Home  To change the WAN settings WAN SetupSelect Advanced Setup WAN Setup Genie Advanced Home Default DMZ Server  To set up a default DMZ server Change the MTU Size To change the MTU size LAN SetupLAN IP address  To change the LAN settings Use Router as Dhcp Server Clear the Use Router as Dhcp Server check box Set Up Address Reservation To disable the Dhcp server feature  To reserve an IP address To edit or delete a reserved address entry Genie Advanced Home Administration Manage your networkManually Update the Router Firmware  To check for new firmware and update your router To back up the router’s configuration settings Manage the Configuration FileBack Up Settings Select Advanced Administration Backup Settings To restore configuration settings that you backed up Restore Configuration SettingsDo not interrupt the reboot process Erase Configuration Settings Advanced Settings Enhance the performance of your routerAdvanced Settings for Your Wireless Network Advanced Wireless Settings To change advanced settings for your wireless network Enable or Disable Wireless Router Radio  To enable or disable the wireless router radioSet Up a Wireless Schedule  To configure and enable the wireless scheduleSet Up the WPS Settings  To change the WPS settings for your wireless networkWireless Distribution System Wireless repeating scenarioSelect Advanced Advanced Setup Wireless Repeating Function Set Up the Base Station To set up the base station Select the Enable Wireless Repeating Function check boxSet Up a Repeater Select the Wireless Base Station radio button To configure the router as a repeater Complete the Repeater IP Address fieldSelect Advanced Advanced Setup Static Routes  To set up a static routeStatic Routes Advanced Settings Universal Plug and Play  To edit or delete a static route To configure Universal Plug and Play Advanced Settings Monitoring Monitor your router and network trafficRouter Status and Usage Information Screen  To display the Router Information pane Router Information PaneInternet Port Pane LAN PortStatistics  To view the traffic statistics To view the connection status Connection StatusDhcp connection PPPoE connection Pptp connectionGuest Network Pane Wireless Settings Pane To display the Wireless Settings pane  To display the Guest Network paneMonitoring Troubleshooting Find and fix problemsQuick Tips Wireless SettingsNetwork Settings Sequence to Restart Your NetworkPower LED Stays Amber Power LED Is Off or BlinkingTroubleshoot with the LEDs Internet or Ethernet Port LEDs Are Off WiFi LED Is OffAll LEDs Remain Lit After Startup WPS Button Blinks AmberCannot Log In to the Router Troubleshoot Internet Browsing Cannot Access the Internet To check the WAN IP address Troubleshoot a PPPoE Internet Connection  To troubleshoot a PPPoE Internet connectionChanges Not Saved Wireless ConnectivityTroubleshoot Your Network Using the Ping Utility Test the LAN Path to Your RouterTest the Path from Your Computer to a Remote Device  To ping the router from a computer running WindowsTroubleshooting Supplemental Information Additional detailsFactory Settings JNR1010v2 router factory default settingsTechnical Specifications JNR1010v2 router specifications

Related manuals

Manual 77 pages 12.78 Kb