NETGEAR JNR1010V2 user manual Default DMZ Server

Page 44

JNR1010v2 N150 Wireless Router

-Secured NAT provides a secured firewall to protect the computers on the LAN from attacks from the Internet, but might prevent some Internet games, point-to-point applications, or multimedia applications from functioning. By default, the Secured radio button is selected.

-Open NAT provides a much less secured firewall, but allows almost all Internet applications to function.

•Disable SIP ALG. Some Voice over IP (VoIP) applications do not function well with the Session Initiation Protocol (SIP) Application Layer Gateway (ALG). Selecting the check box to turn off the SIP ALG might enable connected VoIP devices to create and accept a VoIP call through the router. By default, this check box is cleared.

•Disable IGMP Proxying. IGMP proxying allows computers on the LAN to receive the multicast traffic they are subscribed to from the Internet. By default, this check box is selected, and the IGMP proxy is disabled, preventing multicast traffic from the Internet to the LAN. Clear the Disable IGMP Proxying check box to allow multicast traffic from the Internet to the LAN.

•VPN Passthrough. The router supports VPN passthrough for IPSec, PPTP, and L2TP.

-IPSec Passthrough. To enable or disable IPSec passthrough, select the Enable or Disabled radio button.

-PPTP Passthrough. To enable or disable PPTP passthrough, select the Enable or Disabled radio button.

-L2TP Passthrough. To enable or disable L2TP passthrough, select the Enable or Disabled radio button.

4.Click the Apply button. Your changes are saved.

Default DMZ Server

The default DMZ server feature is helpful when you use some online games and videoconferencing applications that are incompatible with Network Address Translation (NAT). The router is programmed to recognize some of these applications and to function correctly with them, but other applications exist that might not function well. In some cases, one local computer can run the application correctly if that computer’s IP address is entered as the default DMZ server.

WARNING:

DMZ servers pose a security risk. A computer designated as the default DMZ server loses much of the protection of the firewall and is exposed to exploits from the Internet. If compromised, the DMZ server computer can be used to attack other computers on your network.

genie ADVANCED Home

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents JNR1010v2 N150 Wireless Router Trademarks SupportCompliance Contents Administration Appendix a Supplemental Information Hardware Setup Get to know your routerHardware Features Unpack Your RouterFront Panel Router front panel has the following status LEDsJNR1010v2 N150 Wireless Router Front panel LED descriptions Back panel has the following ports, button, and connector Back Panel To position your router Position Your RouterLabel  To prepare your router for installation Cable Your Router Verify the Cabling  To start your networkGet Started with Netgear genie Connect to the routerRouter Setup Preparation Types of Logins and AccessWireless Devices and Security Settings Use Standard TCP/IP Properties for DhcpBrowse to http//routerlogin.net Netgear genie Setup To use Netgear genie to set up your router Log In to Your Router After Installation Upgrade Router FirmwareBasic Home Screen Change the Password Select Advanced Administration Set PasswordSelect the Enable Password Recovery check box Password Recovery To set up password recovery  To recover your password Add Wireless Devices or Computers to Your Network Wi-Fi Protected Setup Method To use WPS to join the wireless network Manual MethodGenie Basic Settings Your Internet connection and networkSelect Basic Internet Internet Setup To view or change the Internet setup Internet IP Address Internet IP Address Basic Wireless Settings Select Basic WirelessGenie Basic Settings Genie Basic Settings WPA-PSK and WPA-PSK + WPA2-PSK Mixed Mode Security Options To configure the WEP security and wireless passphrase WEPGenie Basic Settings Select Basic Attached Devices Attached Devices To view the devices that are connected to your networks Select Basic Guest Network  To set up a guest networkGuest Network Genie Basic Settings Specify custom settings Genie Advanced HomeSetup Wizard  To launch the Setup WizardGenie Advanced Home WPS Wizard  To use the WPS WizardGenie Advanced Home Select Advanced Setup WAN Setup WAN Setup To change the WAN settings Genie Advanced Home Default DMZ Server  To set up a default DMZ server Change the MTU SizeLAN IP address LAN Setup To change the MTU size  To change the LAN settings Use Router as Dhcp Server Set Up Address Reservation  To disable the Dhcp server featureClear the Use Router as Dhcp Server check box  To reserve an IP address To edit or delete a reserved address entry Genie Advanced Home Administration Manage your networkManually Update the Router Firmware  To check for new firmware and update your routerManage the Configuration File Back Up Settings To back up the router’s configuration settings Select Advanced Administration Backup SettingsDo not interrupt the reboot process Restore Configuration Settings To restore configuration settings that you backed up Erase Configuration Settings Advanced Settings Enhance the performance of your router To change advanced settings for your wireless network Advanced Wireless SettingsAdvanced Settings for Your Wireless Network Enable or Disable Wireless Router Radio  To enable or disable the wireless router radioSet Up a Wireless Schedule  To configure and enable the wireless scheduleSet Up the WPS Settings  To change the WPS settings for your wireless networkWireless Distribution System Wireless repeating scenarioSet Up the Base Station  To set up the base stationSelect Advanced Advanced Setup Wireless Repeating Function Select the Enable Wireless Repeating Function check boxSet Up a Repeater Select the Wireless Base Station radio button To configure the router as a repeater Complete the Repeater IP Address fieldStatic Routes  To set up a static routeSelect Advanced Advanced Setup Static Routes Advanced Settings Universal Plug and Play  To edit or delete a static route To configure Universal Plug and Play Advanced Settings Monitoring Monitor your router and network trafficRouter Status and Usage Information Screen Router Information Pane Internet Port Pane To display the Router Information pane LAN PortStatistics  To view the traffic statisticsDhcp connection Connection Status To view the connection status PPPoE connection Pptp connectionWireless Settings Pane  To display the Wireless Settings paneGuest Network Pane  To display the Guest Network paneMonitoring Troubleshooting Find and fix problemsWireless Settings Network SettingsQuick Tips Sequence to Restart Your NetworkTroubleshoot with the LEDs Power LED Is Off or BlinkingPower LED Stays Amber WiFi LED Is Off All LEDs Remain Lit After StartupInternet or Ethernet Port LEDs Are Off WPS Button Blinks AmberCannot Log In to the Router  To check the WAN IP address Cannot Access the InternetTroubleshoot Internet Browsing Troubleshoot a PPPoE Internet Connection  To troubleshoot a PPPoE Internet connectionWireless Connectivity Troubleshoot Your Network Using the Ping UtilityChanges Not Saved Test the LAN Path to Your RouterTest the Path from Your Computer to a Remote Device  To ping the router from a computer running WindowsTroubleshooting Supplemental Information Additional detailsFactory Settings JNR1010v2 router factory default settingsTechnical Specifications JNR1010v2 router specifications
Related manuals
Manual 77 pages 12.78 Kb
Top Page Image Contents