NETGEAR JNR1010V2 user manual Set Up the Base Station,  To set up the base station

Page 63

JNR1010v2 N150 Wireless Router

For you to set up a wireless network in a WDS, the following conditions must be met for both access points:

Both access points must use the same SSID, wireless channel, and encryption mode.

Both access points must be on the same LAN IP subnet. That is, all the access point LAN IP addresses are in the same network.

All LAN devices (wired and wireless computers) must be configured to operate in the same LAN network address range as the access points.

The channel selection on the access points cannot be Auto (see Basic Wireless Settings on page 28).

The security option must be WEP (or no security). The WEP option displays only if you select Up to 54 Mbps from the Mode list on the Wireless Settings screen (see Basic Wireless Settings on page 28).

Set Up the Base Station

The wireless repeating function works only in hub and spoke mode. The units cannot be daisy-chained. You must know the wireless MAC addresses of all units. First, set up the base station and then set up the repeater.

To set up the base station:

1.Log in to the router.

For more information, see Log In to Your Router After Installation on page 18.

2.Select ADVANCED > Advanced Setup > Wireless Repeating Function.

The Wireless Repeating Function screen displays. The wireless MAC address of the router displays onscreen.

3.Select the Enable Wireless Repeating Function check box.

Advanced Settings

63

Image 63
Contents JNR1010v2 N150 Wireless Router Support ComplianceTrademarks Contents Administration Appendix a Supplemental Information Get to know your router Hardware SetupUnpack Your Router Hardware FeaturesRouter front panel has the following status LEDs Front PanelJNR1010v2 N150 Wireless Router Front panel LED descriptions Back Panel Back panel has the following ports, button, and connectorPosition Your Router Label To position your router  To prepare your router for installation Cable Your Router  To start your network Verify the CablingConnect to the router Get Started with Netgear genieUse Standard TCP/IP Properties for Dhcp Router Setup PreparationTypes of Logins and Access Wireless Devices and Security SettingsNetgear genie Setup  To use Netgear genie to set up your routerBrowse to http//routerlogin.net Upgrade Router Firmware Log In to Your Router After InstallationBasic Home Screen Select Advanced Administration Set Password Change the PasswordPassword Recovery  To set up password recoverySelect the Enable Password Recovery check box  To recover your password Manual Method Add Wireless Devices or Computers to Your NetworkWi-Fi Protected Setup Method  To use WPS to join the wireless networkYour Internet connection and network Genie Basic SettingsInternet Setup  To view or change the Internet setupSelect Basic Internet Internet IP Address Internet IP Address Select Basic Wireless Basic Wireless SettingsGenie Basic Settings Genie Basic Settings Security Options WPA-PSK and WPA-PSK + WPA2-PSK Mixed ModeWEP  To configure the WEP security and wireless passphraseGenie Basic Settings Attached Devices  To view the devices that are connected to your networksSelect Basic Attached Devices  To set up a guest network Guest NetworkSelect Basic Guest Network Genie Basic Settings Genie Advanced Home Specify custom settings To launch the Setup Wizard Setup WizardGenie Advanced Home  To use the WPS Wizard WPS WizardGenie Advanced Home WAN Setup  To change the WAN settingsSelect Advanced Setup WAN Setup Genie Advanced Home Default DMZ Server Change the MTU Size  To set up a default DMZ serverLAN Setup  To change the MTU sizeLAN IP address  To change the LAN settings Use Router as Dhcp Server  To reserve an IP address Set Up Address Reservation To disable the Dhcp server feature Clear the Use Router as Dhcp Server check box To edit or delete a reserved address entry Genie Advanced Home Manage your network Administration To check for new firmware and update your router Manually Update the Router FirmwareSelect Advanced Administration Backup Settings Manage the Configuration FileBack Up Settings  To back up the router’s configuration settingsRestore Configuration Settings  To restore configuration settings that you backed upDo not interrupt the reboot process Erase Configuration Settings Enhance the performance of your router Advanced SettingsAdvanced Wireless Settings Advanced Settings for Your Wireless Network To change advanced settings for your wireless network  To enable or disable the wireless router radio Enable or Disable Wireless Router Radio To configure and enable the wireless schedule Set Up a Wireless Schedule To change the WPS settings for your wireless network Set Up the WPS SettingsWireless repeating scenario Wireless Distribution SystemSelect the Enable Wireless Repeating Function check box Set Up the Base Station To set up the base station Select Advanced Advanced Setup Wireless Repeating FunctionSelect the Wireless Base Station radio button Set Up a RepeaterComplete the Repeater IP Address field  To configure the router as a repeater To set up a static route Select Advanced Advanced Setup Static RoutesStatic Routes Advanced Settings  To edit or delete a static route Universal Plug and Play To configure Universal Plug and Play Advanced Settings Monitor your router and network traffic MonitoringRouter Status and Usage Information Screen LAN Port Router Information PaneInternet Port Pane  To display the Router Information pane To view the traffic statistics StatisticsConnection Status  To view the connection statusDhcp connection Pptp connection PPPoE connection To display the Guest Network pane Wireless Settings Pane To display the Wireless Settings pane Guest Network PaneMonitoring Find and fix problems TroubleshootingSequence to Restart Your Network Wireless SettingsNetwork Settings Quick TipsPower LED Is Off or Blinking Power LED Stays AmberTroubleshoot with the LEDs WPS Button Blinks Amber WiFi LED Is OffAll LEDs Remain Lit After Startup Internet or Ethernet Port LEDs Are OffCannot Log In to the Router Cannot Access the Internet Troubleshoot Internet Browsing To check the WAN IP address  To troubleshoot a PPPoE Internet connection Troubleshoot a PPPoE Internet ConnectionTest the LAN Path to Your Router Wireless ConnectivityTroubleshoot Your Network Using the Ping Utility Changes Not Saved To ping the router from a computer running Windows Test the Path from Your Computer to a Remote DeviceTroubleshooting Additional details Supplemental InformationJNR1010v2 router factory default settings Factory SettingsJNR1010v2 router specifications Technical Specifications
Related manuals
Manual 77 pages 12.78 Kb