Sharp UX-P400 operation manual Introduction, Display

Page 3

Introduction

Welcome, and thank you for choosing a Sharp fax machine! The features and specifications of your new Sharp fax are shown below.

Automatic dialling	30 numbers
Imaging film	Initial starter roll (included with machine):
	10 m (approx. 30 A4 pages)
	Replacement roll (not included):
	UX-6CR50 m (one roll yields
	approx. 150 A4 pages)
Memory size*	448 KB (approx. 24 average pages)
Modem speed	9,600 bps with automatic fallback to lower
	speeds.
Transmission time*	Approx. 15 seconds
Resolution	Horizontal: 8 pels/mm
	Vertical:
	Standard: 3.85 lines/mm
	Fine /Halftone: 7.7 lines/mm
	Super fine: 15.4 lines/mm
Automatic document	10 pages max. (A4, 80 g/m2 paper)
feeder
Recording system	Thermal transfer recording
Halftone (grayscale)	64 levels
Compression scheme	MR, MH, H2
Paper tray capacity	Approx. 50 A4-size sheets
(60 - 80 g/m2 paper)	(at room temperature; maximum stack height
	should not be higher than the line on the tray)
Display	16-digit LCD display

*Based on Sharp Standard No.1 Chart at standard resolution is Sharp special mode, excluding time for protocol signals (i.e., ITU-T phase C time only).

1

Image 3

Contents UX-P400/NX-P500 Aviso Display IntroductionIntended use Important safety information Table of Contents Answering Machine Connection Look at the Operation Panel Key COPY/HELP/POLL keySTART/MEMORY key Function keyAbout condensation InstallationUnpacking Checklist Points to keep in mind when setting upConnecting the handset Connecting the power cordConnections Connecting the telephone line cord Switzerland, Austria Attach the paper tray and paper tray extensionOther devices GermanyLoading the Imaging Film Compartment Remove the new roll of imaging film from its packagingInsert the green gears Insert the film into the printInsert the stack of paper into the tray, Print Side Down Loading Printing PaperPrint contrast setting Press Funktion once Twice Entering Your Name and Fax NumberPress Stop to return to the date and time display Setting the Date and Time Press once and onceEnter a two-digit number for the day 01 to Example the 5th Enter the year four digits Example 2001To start the clock Mode Setting the Reception ModeSetting the reception mode TEL/FAX modePress Until the display Volume AdjustmentShows the desired volume level SpeakerIf you selected Ringer OFF OK ? RingerFlash Select Setting for PBX Press Funktion once Once Setting the Display LanguageSize and weight Sending FaxesTransmittable Documents Other restrictions Loading the DocumentResolution settings Adjusting the Resolution and ContrastContrast settings Load the documentsOne or more times until Sending a Fax by Normal Dialling When transmission is completed, the fax will beep once Sending a Fax by Automatic Dialling Storing fax and phone numbers for automatic diallingPress Funktion once Press Speicher Editing and clearing auto-dial numbers Select Edit or ClearMake the desired changes to the name If you are sending a fax, load the documents Using an auto-dial numberReturn to to edit or clear another number, or press Stop to Return to the date and time displaySending a fax by Direct Keypad Dialling Automatic redialling RedialSending a Fax From Memory Broadcasting sending a fax to multiple destinationsEmpfang to set If the memory becomes full Memory transmissionEmpfang until the arrow Using TEL/FAX ModePseudo Ring Duration for Tel/Fax Mode Receiving FaxesUsing A.M. Mode Press once and 3 timesEnter a number as follows for the desired duration Using FAX Mode Changing the number of ringsPress Funktion once and once Using TEL Mode Enter the desired number of rings anyNumber from 2 to Replace the handset Answering with the fax’s handsetPhone goes dead Fax Signal Receive Optional Reception SettingsEnter the desired number any number from 0 to Example 3 Changing the number for remote fax activationPress To turn on the function, or To turn it offReception Ratio Press To select AUTO, or 2 toSelect 100% Substitute Reception to Memory Load the documents face down. Maximum of 10 pages Making CopiesCopy Cut-off Comments Answering Machine ConnectionPreparations Changing the outgoing messageUsing the Answering Machine Connection Set the reception mode to A.MSet your answering machine to auto answer Optional A.M. Mode Settings How answering machine mode operatesQuiet Detect Time Quiet Time On A.M. Failure Quiet Start Quiet Detect Start TimeTo turn off Caller ID, press Caller ID Requires Subscription to ServiceSpecial Functions Press YES to turn on Caller IDDisplay messages How Caller ID operatesDialling and transmission begin Fax Press Stop when you have finished viewing the listViewing the Caller ID list Press TwiceTo delete calls from the Caller ID list Priority CallPress Speicher to store or clear the number Blocking voice calls Blocking Reception of Unwanted Faxes Press Funktion once and twicePress once and twice Press Abruf Polling Requesting a Fax TransmissionPBX operations Making enquiry callsTransferring calls Caller-ID List Setup ListPrinting Lists Telephone Number ListHeadings in Transaction Report Transaction ReportHelp List Transaction Report print conditionPrint head MaintenanceScanning glass and rollers MaintenanceIf the scanning glass is difficult to clean HousingProblem Solution TroubleshootingProblems and Solutions Line errorCorrect socket. See Connecting the handset on Dialling and transmission problemsReception and copying problems Answering machine connection See Loading the Imaging Film on General problemsPress Start KEY Messages and SignalsSubstitute Reception to Memory on page 48. If you Recalling Audible signalsClearing a jammed document Clearing Paper JamsClearing jammed printing paper Sending Faxes Quick Reference GuideIndex Index Page Sharp Electronics Europe Gmbh