AEG Thyro-S H1 manual Interfaces, System interface, Ethernet interfaces

Page 29

8. Interfaces

8.1 System interface

The bus module is connected with the relevant system interfaces of the power controllers via X1 to X8 (four-wire, 2x2 twisted, shared shielding).

The transmission rate is 38,400 Bd.

The asynchronous characters are transferred with 8bit, no parity, one stop bit. The protocol begins with STX, followed by an identifier, the data, and is concluded with a check sum. Defective protocols are ignored.

8.2 Ethernet interfaces

Communication medium	CAT 5e
Network topology	tree, star and line
Maximum cable length	100m
ProfiNET-participants	restricted to the maximum supported number of devices by the con-
	troller used
PNO identification number0x0188
Device ID	0x0001
Transmission rate	100 Mbit/s

Image 29

Contents Ethernet Bus Module ProﬁNet Contents List of figures and tables Contact Introduction Identification in the operating instructions SafetyGeneral danger information Electric currentPersonnel requirements Operator requirementsIntended use Use of the deviceTransport Prior to installation / commissioningMaintenance, service, faults Processing the setpoint Thyro-A FunctionsProcessing the setpoint Thyro-S Relais Control Processing the setpoint Thyro-Step ControllerFreely addressable digital outputs Connecting a 24 V power supply InstallationConnecting the power controller to Connecting the Ethernet bus module to the masterSetting the protocol SettingsSetting the number of slots Setting the device nameOperating display of the bus module Operating display of the bus moduleOperating status of the Ethernet bus module Status LED of the Ethernet PortsCyclical data transmission configuration Start configuration parameterizationOperation Input and output data Thyro-STab Interpretation of the master setpoint with Thyro-S Tab b Thyro-S FaultsTab Cyclic input and output data with Thyro-S ..H1 Tab Cyclic input and output data with Thyro-S ..HRL1Tab b Thyro-S Status Input and output data Thyro-ATab Cyclic input and output data with Thyro-A 1A...H1 Tab Cyclic input and output data with Thyro-A 1A...HRL1Tab Cyclic input and output data with Thyro-A 2A...HRL1 Tab Cyclic input and output data with Thyro-A 1A...HRLP1Tab Cyclic input and output data with Thyro-A 2A...H1 Tab Cyclic input and output data with Thyro-A 3A...H1 Tab Cyclic input and output data with Thyro-A 2A...HRLP1Tab Cyclic input and output data with Thyro-A 3A...HRLP1 Tab Cyclic input and output data with Thyro-A 3A...HRL1Tab b Thyro-A Status Tab a Thyro-A FaultTab Cyclic input and output data with Thyro-A 1A...C03 Tab Cyclic input and output data with Thyro-A 1A...C01Tab Cyclic input and output data with Thyro-A 1A...C02 Tab Cyclic input and output data with Thyro-A 1A...C07 Tab Cyclic input and output data with Thyro-A 1A...C05Supported operating modes TPM TSC TMU Tab Supported operating modesTab Cyclic input and output data TPM manual mode Input and output data Thyro-Power ManagerTab Cyclic input and output data TPM automatic mode Tab Cyclic input and output data TIO mode Tab Cyclic input and output data TSC modeInput and output data Thyro-Step Controller Input and output data Thyro Input/Output UnitTab b Fault TPM, TSC, TIO, TMU Tab Cyclic input and output data TMU modeInput and output data Thyro-Measurement Unit Tab b Status TPM, TSC, TIO, TMUWrite data record Wrrec Acyclic data transmission parameterizationRead data record Rdrec External connections Power supplyOperating elements and terminal blocks Ethernet interfaces InterfacesSystem interface Connection diagram Thyro-A Connection diagrams Thyro-AConnection diagram Thyro-S Connection diagrams Thyro-SConnection diagram TSC Connection diagrams TSCInstallation Technical DataService Specific notesApprovals and conformity Dimension drawingsAccessories and options Detail Controller parameter Appendix aHRL1 Hrlp SST RLP1 U16 R309 Index R309 DAC1OF Page Type value U mains U16 …260 Measuring and cycle time …1500