AEG Thyro-S H1 manual Tab a Thyro-A Fault, Tab b Thyro-A Status

Page 20

Tab. 14a Thyro-A Fault

Description	Bit	LEDs	Relay
Frequency measurement outside of 47Hz to 63Hz	Bit 0	Pulse Inhibit LED flashing slowly	open
SYNC error, no cero crossing within the gate	Bit 1	Pulse Inhibit LED flashing slowly	open
Temperature monitoring triggered	Bit 2	Load Fault LED flashing slowly	open
Load fault	Bit 3	Load fault LED on	open
Flash values invalid	Bit 4	Pulse Inhibit LED and Load	open
		Fault LED flashing simultaneous-
		ly qickly
Mains undervoltage (<AD_P_SPG_MIN)	Bit 5	Pulse Inhibit LED, Load Fault	open
		LED and test LED on

Mains overvoltage (>AD_P_SPG_MAX) Master / slave fault (only with2A) Undervoltage limit

Overvoltage limit Undercurrent limit Overcurrent limit Low power limit High power limit

Bit 6	none
Bit 8	none
Bit 9	none
Bit 10	none
Bit 11	none
Bit 12	none
Bit 13	none
Bit 14	none

open

closed closed closed closed closed closed closed

Tab. 14b Thyro-A Status

Description	Bit	LEDs		Relay
Pulse inhib active (bridge X2.1-X2.2 open)	Bit 0	Pulse Inhibit LED on		closed
Mains frequency is 60Hz	Bit 2	none		closed
U-limiting	Bit 4	Pulse Inhibit LED	and Load	closed
		Fault LED flashing alternately
		slowly
I-limiting	Bit 5	Pulse Inhibit LED	and Load	closed
		Fault LED flashing alternately
		slowly
P-limiting	Bit 6	Pulse Inhibit LED	and Load	closed
		Fault LED flashing alternately
		slowly
Relay status	Bit 8	none		on/off
(0=relay off / 1=relay on)	Bit 8	none		on/off
Device switched off	Bit 9	--		--
Wrong device	Bit 10	--		--
Bus module active	Bit 11	only with Thyro-S		-----
(0=no bus module / 1=bus module active)
Thyristor short-circuit	Bit 14	only with Thyro-S		----
Failure rotating field / phase	Bit 15	none		closed
(only Thyro 2A or 3A)	Bit 15	Pulse Inhibit LED	and Test LED	closed
		flashing simultaneously slowly
Overcurrent limit	Bit 12	none		closed
Low power limit	Bit 13	none		closed
High power limit	Bit 14	none		closed

20

Image 20

Contents Ethernet Bus Module ProﬁNet Contents List of figures and tables Contact Introduction Safety Identification in the operating instructionsGeneral danger information Electric currentOperator requirements Personnel requirementsIntended use Use of the deviceTransport Prior to installation / commissioningMaintenance, service, faults Processing the setpoint Thyro-A FunctionsProcessing the setpoint Thyro-S Relais Control Processing the setpoint Thyro-Step ControllerFreely addressable digital outputs Installation Connecting a 24 V power supplyConnecting the power controller to Connecting the Ethernet bus module to the masterSettings Setting the protocolSetting the number of slots Setting the device nameOperating display of the bus module Operating display of the bus moduleOperating status of the Ethernet bus module Status LED of the Ethernet PortsStart configuration parameterization Cyclical data transmission configurationOperation Input and output data Thyro-STab b Thyro-S Faults Tab Interpretation of the master setpoint with Thyro-STab Cyclic input and output data with Thyro-S ..H1 Tab Cyclic input and output data with Thyro-S ..HRL1Input and output data Thyro-A Tab b Thyro-S StatusTab Cyclic input and output data with Thyro-A 1A...H1 Tab Cyclic input and output data with Thyro-A 1A...HRL1Tab Cyclic input and output data with Thyro-A 2A...HRL1 Tab Cyclic input and output data with Thyro-A 1A...HRLP1Tab Cyclic input and output data with Thyro-A 2A...H1 Tab Cyclic input and output data with Thyro-A 2A...HRLP1 Tab Cyclic input and output data with Thyro-A 3A...H1Tab Cyclic input and output data with Thyro-A 3A...HRL1 Tab Cyclic input and output data with Thyro-A 3A...HRLP1Tab a Thyro-A Fault Tab b Thyro-A StatusTab Cyclic input and output data with Thyro-A 1A...C03 Tab Cyclic input and output data with Thyro-A 1A...C01Tab Cyclic input and output data with Thyro-A 1A...C02 Tab Cyclic input and output data with Thyro-A 1A...C05 Tab Cyclic input and output data with Thyro-A 1A...C07Supported operating modes TPM TSC TMU Tab Supported operating modesTab Cyclic input and output data TPM manual mode Input and output data Thyro-Power ManagerTab Cyclic input and output data TPM automatic mode Tab Cyclic input and output data TSC mode Tab Cyclic input and output data TIO modeInput and output data Thyro-Step Controller Input and output data Thyro Input/Output UnitTab Cyclic input and output data TMU mode Tab b Fault TPM, TSC, TIO, TMUInput and output data Thyro-Measurement Unit Tab b Status TPM, TSC, TIO, TMUWrite data record Wrrec Acyclic data transmission parameterizationRead data record Rdrec Power supply External connectionsOperating elements and terminal blocks Ethernet interfaces InterfacesSystem interface Connection diagrams Thyro-A Connection diagram Thyro-AConnection diagrams Thyro-S Connection diagram Thyro-SConnection diagrams TSC Connection diagram TSCTechnical Data InstallationService Specific notesApprovals and conformity Dimension drawingsAccessories and options Detail Appendix a Controller parameterHRL1 Hrlp SST RLP1 U16 R309 Index R309 DAC1OF Page Type value U mains U16 …260 Measuring and cycle time …1500