AEG Thyro-S H1 Prior to installation / commissioning, Maintenance, service, faults, Transport

Page 8

2.6.2Prior to installation / commissioning

-If stored in a cold environment: ensure that the device is absolutely dry. (Allow the device a period of at least two hours to acclimatize before commissioning)

-Ensure sufficient ventilation of the cabinet if mounted in a cabinet.

-Observe minimum spacing.

-Ensure that the device cannot be heated up by heat sources below it. (see page 33, Technical data).

-Ground the device in accordance with local regulations.

-Connect the device in accordance with the connection diagrams.

2.6.3Maintenance, service, faults

In order to avoid personal and material damages, the user must observe the following:

-Before all work:

>Disconnect the device from all external voltage sources.

>Secure the device against accidentally being switched back on.

>Use suitable measuring instruments and check that there is no voltage present.

>Ground and short circuit the device.

>Provide protection by covers or barriers for any neighboring live parts.

-The device may only be serviced and repaired by trained electro-technical personnel.

2.6.4Transport

-Only transport the device in the original packaging.

-Protect the device against damage, caused by jolts, knocks and contamination, for instance.

8

Image 8

Contents Ethernet Bus Module ProﬁNet Contents List of figures and tables Contact Introduction Safety Identification in the operating instructionsGeneral danger information Electric currentOperator requirements Personnel requirementsIntended use Use of the deviceTransport Prior to installation / commissioningMaintenance, service, faults Processing the setpoint Thyro-A FunctionsProcessing the setpoint Thyro-S Relais Control Processing the setpoint Thyro-Step ControllerFreely addressable digital outputs Installation Connecting a 24 V power supplyConnecting the power controller to Connecting the Ethernet bus module to the masterSettings Setting the protocolSetting the number of slots Setting the device nameOperating display of the bus module Operating display of the bus moduleOperating status of the Ethernet bus module Status LED of the Ethernet PortsStart configuration parameterization Cyclical data transmission configurationOperation Input and output data Thyro-STab b Thyro-S Faults Tab Interpretation of the master setpoint with Thyro-STab Cyclic input and output data with Thyro-S ..H1 Tab Cyclic input and output data with Thyro-S ..HRL1Input and output data Thyro-A Tab b Thyro-S StatusTab Cyclic input and output data with Thyro-A 1A...H1 Tab Cyclic input and output data with Thyro-A 1A...HRL1Tab Cyclic input and output data with Thyro-A 2A...HRL1 Tab Cyclic input and output data with Thyro-A 1A...HRLP1Tab Cyclic input and output data with Thyro-A 2A...H1 Tab Cyclic input and output data with Thyro-A 2A...HRLP1 Tab Cyclic input and output data with Thyro-A 3A...H1Tab Cyclic input and output data with Thyro-A 3A...HRL1 Tab Cyclic input and output data with Thyro-A 3A...HRLP1Tab a Thyro-A Fault Tab b Thyro-A StatusTab Cyclic input and output data with Thyro-A 1A...C03 Tab Cyclic input and output data with Thyro-A 1A...C01Tab Cyclic input and output data with Thyro-A 1A...C02 Tab Cyclic input and output data with Thyro-A 1A...C05 Tab Cyclic input and output data with Thyro-A 1A...C07Supported operating modes TPM TSC TMU Tab Supported operating modesTab Cyclic input and output data TPM manual mode Input and output data Thyro-Power ManagerTab Cyclic input and output data TPM automatic mode Tab Cyclic input and output data TSC mode Tab Cyclic input and output data TIO modeInput and output data Thyro-Step Controller Input and output data Thyro Input/Output UnitTab Cyclic input and output data TMU mode Tab b Fault TPM, TSC, TIO, TMUInput and output data Thyro-Measurement Unit Tab b Status TPM, TSC, TIO, TMUWrite data record Wrrec Acyclic data transmission parameterizationRead data record Rdrec Power supply External connectionsOperating elements and terminal blocks Ethernet interfaces InterfacesSystem interface Connection diagrams Thyro-A Connection diagram Thyro-AConnection diagrams Thyro-S Connection diagram Thyro-SConnection diagrams TSC Connection diagram TSCTechnical Data InstallationService Specific notesApprovals and conformity Dimension drawingsAccessories and options Detail Appendix a Controller parameterHRL1 Hrlp SST RLP1 U16 R309 Index R309 DAC1OF Page Type value U mains U16 …260 Measuring and cycle time …1500