ADC HDSL4, H4TU-C-319 List 1 Line Unit user manual Appendix B Functional Operation

Page 6

Table of Contents

LTPH-UM-1031-03, Issue 3

System Alarms

42

Alarm Option for DLC Feed

44

Retiring System Alarms

44

Remote LOS and AIS Response

45

OCT55 Test Pattern with AMI Line Code

45

Loopback Operation

46

Generic Loopback Commands

47

Special Loopback Commands

47

Manual Loopback Session

48

Loopback Test Procedures

49

General Troubleshooting Tips

49

GNLB Test Procedures

51

A3LB Test Procedure

52

A5LB Test Procedure

53

Testing with H4TU-C BERT Generator

56

Testing with H4TU-R BERT Generator

57

Appendix A - Specifications ____________________________________________________________ 58

Power Consumption

60

Maximum Power Dissipation

60

Maximum Current Drain

61

Loop Attenuation, Insertion Loss, and Reach

61

H4TU-C-319Card-Edge Connector

62

Network Management Control Bus

62

Fuse Alarm

62

System Alarm Output Pin

63

Craft Port

63

Appendix B - Functional Operation _____________________________________________________ 64

Timing

64

Ground Fault Detection

64

Spectrum Issues

64

Appendix C - Compatibility____________________________________________________________ 65

Appendix D - Product Support _________________________________________________________ 66

Appendix E - Abbreviations____________________________________________________________ 67

Certification and Warranty ____________________________________________________________ 70

vi

September 12, 2003

H4TU-C-319 List 1

Image 6
Contents HDSL4 H4TU-C-319 List 1 Line Unit2001 Initial release March 15 IssueDate Revisions Made September 12Using this Manual Inspecting ShipmentInspecting Shipment Table of Contents Appendix B Functional Operation Config Menu List of FiguresNavigational Keys for the Maintenance Terminal Screens List of TablesFeatures OverviewApplications Front Panel H4TU-C-319 List 1 Front PanelBRG Front-Panel Feature FunctionFront-Panel Description LineFront-Panel Display Messages Message Full Name DescriptionDiagnostic Messages Loopback MessagesSystem Information Messages a Code Line Code AMI, B8ZS Marg Margin Current margin threshold setting measured in dBFRM Frame SF, ESF, Unfr Substitution B8ZSInstallation Installing the H4TU-C-319 List 1 into a ShelfVerification Verification without a Downstream DeviceVerification with a Downstream Device Using the Mode and SEL Pushbuttons Setting Options through Mode and SELProvisioning Disabling an Alarm Resetting to Factory DefaultDisplaying System Parameter Settings Loopback ModesNavigational Keys for the Maintenance Terminal Screens Using a Maintenance TerminalConnecting to a Maintenance Terminal Logon ScreenPress this key Menu FunctionsPress this key To access this menu Menu Functions Setting Date and Time Provisioning TasksSetting Circuit ID Numbers Inventory ScreenConfiguring the System Config MenuConfig Menu Standard Options defaults shown 38 dB H4TU-C-319 List 1 Standard Config Menu Options60 min AutoDIS H4TU-C-319 List 1 ADC Config Menu OptionsADC Config Menu Screen Selection Description Options DEFLpbk HDSL4 BER HberNone ALM ENADS1/DSX-1 24-Hour PM Threshold ParameterResetting to Factory Defaults Clearing the History, Alarm, and Event Log Screens Config Menu Master ClearUsing the Monitor Screen to View System Activity Monitoring System Activity and PerformanceSystem Overview Monitor Screen Descriptions Field DescriptionMAL Insl LPFPRM Using the Performance Screens to View Performance Data Performance History at the DS1 InterfaceH4TU-C DS1 25-Hour Performance History H4TU-R DS1 Current Statistics Acronyms Used on the DS1 Performance History Screens Acronym DescriptionPerformance History at the HDSL4 Interface H4TU-C Hdsl Loop 1/Loop 2 31-Day Performance HistoryH4TU-C Hdsl Loop 1/Loop 2 25-Hour Performance History UAS Acronyms Used on the HDSL4 Performance History ScreensSES LoswsUsing the Performance Screens to View Alarm Data Alarm History at the DS1 InterfaceRAI Rrai Screen Alarm Front-PanelDescription H4TU-C DS1 Alarms onH4TU-R DS1 Alarms on this PRM-NE PrmnAlarm History at the HDSL4 Interface HDSL4 Alarms at the H4TU-C onlyUsing the Event LOG to Track System Events System Event LogEvent Log Entry Messages List Event Log MessagesPRM-FE Using the Report Menu Report Menu Full ReportReport Types Type Contains the following informationFront-Panel System Alarms TestingSystem Alarms Front-Panel Alarm Description To Inhibit Message aFront-Panel Alarm Description PrmnAlarm Option for DLC Feed Retiring System AlarmsOCT55 Test Pattern with AMI Line Code Remote LOS and AIS ResponseLoopback Operation Loopback SummaryGeneric Loopback Commands Special Loopback CommandsSetting the Loopback Time-Out Option Lbto Manual Loopback SessionLoopback Test Procedures General Troubleshooting TipsLoopback Modes Loopback Code Description Test Set Craft Port Gnlb Test ProceduresSummary of HDSL4 Loopback and Activation Codes MODE/SELA3LB Test Procedure A3LB Addressable Repeater Loopback CommandsName A5LB Test Procedure A5LB Addressable Repeater Loopback CommandsTesting LTPH-UM-1031-03, Issue Bert Signal Pattern Testing with H4TU-C Bert GeneratorBert Signal Generator Option DescriptionTesting with H4TU-R Bert Generator H4TU-R Bert Generator ScreenAppendix a Specifications HDSL4One-way DS1 Delay 700 µs Wander Looped SystemWideband Jitter Looped UI maximum Narrowband Jitter Looped Power Consumption Maximum Power DissipationH4TU-C Power Parameters Loop ATTENUATION, Insertion LOSS, and Reach HDSL4 Reach ChartMaximum Current Drain 196 KHz dB/kftFuse Alarm Network Management Control BusSystem Alarm Output Pin Craft PortAppendix B Functional Operation Ground Fault DetectionSpectrum Issues TimingAppendix C Compatibility Systems Integration Appendix D Product SupportSales Assistance Online Technical Support Online Technical PublicationsAppendix E Abbreviations Lbpv LaisLatt LbtoLTPH-UM-1031-03, Issue Certification and Warranty FCC Class a Compliance Limited WarrantyWorld Headquarters For Technical Assistance