ADC H4TU-C-319 List 1 Line Unit, HDSL4 user manual Provisioning Tasks, Setting Date and Time

Page 23

LTPH-UM-1031-03, Issue 3	Provisioning

PROVISIONING TASKS

After the H4TU-C-319 is successfully installed, perform these basic provisioning tasks:

1Set the date and time (see “Setting Date and Time” on this page).

2Set the circuit ID numbers (see “Setting Circuit ID Numbers” on page 16).

3Make any desired changes to configuration (see “Configuring the System” on page 17).

4Clear history, alarm, and event log screens to remove miscellaneous data during startup (see “Clearing the History, Alarm, and Event Log Screens” on page 24).

Setting Date and Time

Monitor	Performance Event Log	Config	Inventory	Report Rlogon			Help
	----------------------+				+
		Standard Options ->
		ADC Options		->
	BERT Generator			->
		Date and Time		->

+-------------------------------			+
Date (mm/dd/yyyy):	02/01/2002
Time (hh:mm[:ss]):	12:30:01
+-------------------------------			+

ID: xxxx--xxxx—-xxxx--xxxx

02/01/2002 12:30:01

H4TU-C

System: OK___

Figure 4. Config Menu - Date and Time

1Press C to select the Config menu.

2Use the ↑ and ↓ arrow keys to select Date and Time, then press ENTER .

3Type the date in the format indicated, then press ENTER .

4Type the time in the format indicated (entering seconds is optional), then press ENTER .

H4TU-C-319 List 1

September 12, 2003

15

Image 23

Contents H4TU-C-319 List 1 Line Unit HDSL4September 12 IssueDate Revisions Made 2001 Initial release March 15Inspecting Shipment Using this ManualInspecting Shipment Table of Contents Appendix B Functional Operation List of Figures Config MenuList of Tables Navigational Keys for the Maintenance Terminal ScreensOverview FeaturesApplications H4TU-C-319 List 1 Front Panel Front PanelLine Front-Panel Feature FunctionFront-Panel Description BRGMessage Full Name Description Front-Panel Display MessagesSystem Information Messages a Diagnostic MessagesLoopback Messages Substitution B8ZS Marg Margin Current margin threshold setting measured in dBFRM Frame SF, ESF, Unfr Code Line Code AMI, B8ZSInstalling the H4TU-C-319 List 1 into a Shelf InstallationVerification with a Downstream Device VerificationVerification without a Downstream Device Provisioning Using the Mode and SEL PushbuttonsSetting Options through Mode and SEL Loopback Modes Resetting to Factory DefaultDisplaying System Parameter Settings Disabling an AlarmLogon Screen Using a Maintenance TerminalConnecting to a Maintenance Terminal Navigational Keys for the Maintenance Terminal ScreensMenu Functions Press this keyPress this key To access this menu Menu Functions Provisioning Tasks Setting Date and TimeInventory Screen Setting Circuit ID NumbersConfig Menu Configuring the SystemConfig Menu Standard Options defaults shown Auto H4TU-C-319 List 1 Standard Config Menu Options60 min 38 dBDEF H4TU-C-319 List 1 ADC Config Menu OptionsADC Config Menu Screen Selection Description Options DISALM ENA HDSL4 BER HberNone LpbkParameter DS1/DSX-1 24-Hour PM ThresholdResetting to Factory Defaults Config Menu Master Clear Clearing the History, Alarm, and Event Log ScreensSystem Overview Using the Monitor Screen to View System ActivityMonitoring System Activity and Performance MAL Monitor Screen DescriptionsField Description PRM InslLPF Performance History at the DS1 Interface Using the Performance Screens to View Performance DataH4TU-C DS1 25-Hour Performance History H4TU-R DS1 Current Statistics Acronym Description Acronyms Used on the DS1 Performance History ScreensH4TU-C Hdsl Loop 1/Loop 2 31-Day Performance History Performance History at the HDSL4 InterfaceH4TU-C Hdsl Loop 1/Loop 2 25-Hour Performance History Losws Acronyms Used on the HDSL4 Performance History ScreensSES UASAlarm History at the DS1 Interface Using the Performance Screens to View Alarm DataPRM-NE Prmn Screen Alarm Front-PanelDescription H4TU-C DS1 Alarms onH4TU-R DS1 Alarms on this RAI RraiHDSL4 Alarms at the H4TU-C only Alarm History at the HDSL4 InterfaceSystem Event Log Using the Event LOG to Track System EventsPRM-FE Event Log Entry Messages ListEvent Log Messages Report Menu Full Report Using the Report MenuType Contains the following information Report TypesFront-Panel Alarm Description To Inhibit Message a TestingSystem Alarms Front-Panel System AlarmsPrmn Front-Panel Alarm DescriptionRetiring System Alarms Alarm Option for DLC FeedRemote LOS and AIS Response OCT55 Test Pattern with AMI Line CodeLoopback Summary Loopback OperationSpecial Loopback Commands Generic Loopback CommandsManual Loopback Session Setting the Loopback Time-Out Option LbtoGeneral Troubleshooting Tips Loopback Test ProceduresLoopback Modes MODE/SEL Gnlb Test ProceduresSummary of HDSL4 Loopback and Activation Codes Loopback Code Description Test Set Craft PortName A3LB Test ProcedureA3LB Addressable Repeater Loopback Commands A5LB Addressable Repeater Loopback Commands A5LB Test ProcedureTesting LTPH-UM-1031-03, Issue Option Description Testing with H4TU-C Bert GeneratorBert Signal Generator Bert Signal PatternH4TU-R Bert Generator Screen Testing with H4TU-R Bert GeneratorHDSL4 Appendix a SpecificationsWideband Jitter Looped UI maximum Narrowband Jitter Looped One-way DS1 Delay 700 µs Wander LoopedSystem H4TU-C Power Parameters Power ConsumptionMaximum Power Dissipation 196 KHz dB/kft HDSL4 Reach ChartMaximum Current Drain Loop ATTENUATION, Insertion LOSS, and ReachNetwork Management Control Bus Fuse AlarmCraft Port System Alarm Output PinTiming Ground Fault DetectionSpectrum Issues Appendix B Functional OperationAppendix C Compatibility Online Technical Support Online Technical Publications Appendix D Product SupportSales Assistance Systems IntegrationAppendix E Abbreviations Lbto LaisLatt LbpvLTPH-UM-1031-03, Issue FCC Class a Compliance Limited Warranty Certification and WarrantyFor Technical Assistance World Headquarters