ADC HDSL4 user manual Installation, Installing the H4TU-C-319 List 1 into a Shelf

Page 16

Installation	LTPH-UM-1031-03, Issue 3

INSTALLATION

Upon receipt of the equipment, inspect the contents for signs of damage. If the equipment has been damaged in transit, immediately report the extent of damage to the transportation company and to ADC.

H4TU-C-319

CO shelf

Figure 2. Installing the H4TU-C-319 List 1 into a Shelf

When installing an H4TU-C in a chassis, be sure to wear an antistatic wrist strap. Avoid touching components on the circuit board.

To comply with the intrabuilding wiring requirements of GR-1089 CORE, Section 4.5.9, the shields of the ABAM-type cables that connect the H4TU-C DSX-1 output ports to the cross-connect panel must be grounded at both ends.

1Align the H4TU-C with the enclosure slot guides, then push the unit in until it touches the backplane card-edge connector.

2Place your thumbs on the front panel and push the H4TU-C into the slot guides until properly seated.

8

September 12, 2003

H4TU-C-319 List 1

Image 16

Contents HDSL4 H4TU-C-319 List 1 Line UnitIssue Date Revisions Made2001 Initial release March 15 September 12Using this Manual Inspecting ShipmentInspecting Shipment Table of Contents Appendix B Functional Operation Config Menu List of FiguresNavigational Keys for the Maintenance Terminal Screens List of TablesFeatures OverviewApplications Front Panel H4TU-C-319 List 1 Front PanelFront-Panel Feature Function Front-Panel DescriptionBRG LineFront-Panel Display Messages Message Full Name DescriptionLoopback Messages Diagnostic MessagesSystem Information Messages a Marg Margin Current margin threshold setting measured in dB FRM Frame SF, ESF, UnfrCode Line Code AMI, B8ZS Substitution B8ZSInstallation Installing the H4TU-C-319 List 1 into a ShelfVerification without a Downstream Device VerificationVerification with a Downstream Device Setting Options through Mode and SEL Using the Mode and SEL PushbuttonsProvisioning Resetting to Factory Default Displaying System Parameter SettingsDisabling an Alarm Loopback ModesUsing a Maintenance Terminal Connecting to a Maintenance TerminalNavigational Keys for the Maintenance Terminal Screens Logon ScreenPress this key Menu FunctionsPress this key To access this menu Menu Functions Setting Date and Time Provisioning TasksSetting Circuit ID Numbers Inventory ScreenConfiguring the System Config MenuConfig Menu Standard Options defaults shown H4TU-C-319 List 1 Standard Config Menu Options 60 min38 dB AutoH4TU-C-319 List 1 ADC Config Menu Options ADC Config Menu Screen Selection Description OptionsDIS DEFHDSL4 BER Hber NoneLpbk ALM ENADS1/DSX-1 24-Hour PM Threshold ParameterResetting to Factory Defaults Clearing the History, Alarm, and Event Log Screens Config Menu Master ClearMonitoring System Activity and Performance Using the Monitor Screen to View System ActivitySystem Overview Field Description Monitor Screen DescriptionsMAL LPF InslPRM Using the Performance Screens to View Performance Data Performance History at the DS1 InterfaceH4TU-C DS1 25-Hour Performance History H4TU-R DS1 Current Statistics Acronyms Used on the DS1 Performance History Screens Acronym DescriptionPerformance History at the HDSL4 Interface H4TU-C Hdsl Loop 1/Loop 2 31-Day Performance HistoryH4TU-C Hdsl Loop 1/Loop 2 25-Hour Performance History Acronyms Used on the HDSL4 Performance History Screens SESUAS LoswsUsing the Performance Screens to View Alarm Data Alarm History at the DS1 InterfaceScreen Alarm Front-PanelDescription H4TU-C DS1 Alarms on H4TU-R DS1 Alarms on thisRAI Rrai PRM-NE PrmnAlarm History at the HDSL4 Interface HDSL4 Alarms at the H4TU-C onlyUsing the Event LOG to Track System Events System Event LogEvent Log Messages Event Log Entry Messages ListPRM-FE Using the Report Menu Report Menu Full ReportReport Types Type Contains the following informationTesting System AlarmsFront-Panel System Alarms Front-Panel Alarm Description To Inhibit Message aFront-Panel Alarm Description PrmnAlarm Option for DLC Feed Retiring System AlarmsOCT55 Test Pattern with AMI Line Code Remote LOS and AIS ResponseLoopback Operation Loopback SummaryGeneric Loopback Commands Special Loopback CommandsSetting the Loopback Time-Out Option Lbto Manual Loopback SessionLoopback Test Procedures General Troubleshooting TipsLoopback Modes Gnlb Test Procedures Summary of HDSL4 Loopback and Activation CodesLoopback Code Description Test Set Craft Port MODE/SELA3LB Addressable Repeater Loopback Commands A3LB Test ProcedureName A5LB Test Procedure A5LB Addressable Repeater Loopback CommandsTesting LTPH-UM-1031-03, Issue Testing with H4TU-C Bert Generator Bert Signal GeneratorBert Signal Pattern Option DescriptionTesting with H4TU-R Bert Generator H4TU-R Bert Generator ScreenAppendix a Specifications HDSL4System One-way DS1 Delay 700 µs Wander LoopedWideband Jitter Looped UI maximum Narrowband Jitter Looped Maximum Power Dissipation Power ConsumptionH4TU-C Power Parameters HDSL4 Reach Chart Maximum Current DrainLoop ATTENUATION, Insertion LOSS, and Reach 196 KHz dB/kftFuse Alarm Network Management Control BusSystem Alarm Output Pin Craft PortGround Fault Detection Spectrum IssuesAppendix B Functional Operation TimingAppendix C Compatibility Appendix D Product Support Sales AssistanceSystems Integration Online Technical Support Online Technical PublicationsAppendix E Abbreviations Lais LattLbpv LbtoLTPH-UM-1031-03, Issue Certification and Warranty FCC Class a Compliance Limited WarrantyWorld Headquarters For Technical Assistance