GE BECCO2200 manual Type 1 Read Interval, Type 2 Read Interval, Type 3 Read Interval

Page 31

BECCO2200 DCA
Configuration Guide	GE Energy Services

5.2.4 Type 1 Read Interval

This parameter specifies, in seconds, the minimum interval between Type 1 Read requests issued to the device. A negative number configured indicates that no timed scans of this type are required for this device. The device may, at any time, scanned through the activation of the Type 1 Read Pseudo Control.

5.2.5 Type 2 Read Interval

This parameter specifies, in seconds, the minimum interval between Type 2 Read requests issued to the device. A negative number configured indicates that no timed scans of this type are required for this device. The device may, at any time, be scanned through the activation of the Type 2 Read Pseudo Control.

5.2.6 Type 3 Read Interval

This parameter specifies, in seconds, the minimum interval between Type 3 Read requests issued to the device. A negative number configured indicates that no timed scans of this type are required for this device. The device may, at any time, be scanned through the activation of the Type 3 Read Pseudo Control.

☞NOTE: Use Type 7 Read for Consecutive Status instead of Type 3 Read.

5.2.7 Type 4 Read Interval

This parameter specifies, in seconds, the minimum interval between Type 4 Read requests issued to the device. A negative number configured indicates that no timed scans of this type are required for this device. The device may, at any time, be scanned through the activation of the Type 4 Read Pseudo Control.

5.2.8 Type 5 Read Interval

This parameter specifies, in seconds, the minimum interval between Type 5 Read requests issued to the device. A negative number configured indicates that no timed scans of this type are required for this device. The device may, at any time, be scanned through the activation of the Type 5 Read Pseudo Control.

5.2.9 Type 6 Read Interval

This parameter specifies, in seconds, the minimum interval between Type 6 Read requests issued to the device. A negative number configured indicates that no timed scans of this type are required for this device. The device may, at any time, be scanned through the activation of the Type 6 Read Pseudo Control.

Restricted

A164-0CG-1.00-2

Full	15

Image 31

Contents BECCO2200 DCA Configuration GuideTrademark Notices Table of Contents Configuring the A164MODE Table Configuring the A164DTBL Configuration Table BECCO2200 DCA List of Figures Viii List of Tables BECCO2200 DCA Purpose of this Guide About this GuideWho Should Use this Guide Introduction to the Wesdac D20 RTU GEN-0003 Additional DocumentationHow this Guide is Organized Xiv Overview Xvi BECO2200 DCA Configuration Tables Configuration TablesConfiguration Sequence Wesdac Point Allocation Configuring Win for the BECO2200 DCAAnalog Inputs Binary InputsBinary Outputs CountersGeneral Information Configuring the A164APPL TableDescription of Fields SOE Buffer Overflow Option Reply Buffer Size AdjustmentSOE Buffer Size Adjustment DCA IndexDevice Event Response Time BECCO2200 DCA BECO2200 DCA A164PORT Configuration Table Configuring the A164PORT TableRTS On Time Communication Port NameCommunication Port Parity Baud RateRemote Reply Timeout Intercharacter TimeoutRTS Off Time Number of Devices on Port Line Idle TimeRetries Before Failure Failures Before Off-lineBECO2200 DCA A164UNIT Configuration Table Configuring the A164UNIT TableUnit Type Remote AddressType 0 Read Interval Type 4 Read Interval Type 1 Read IntervalType 2 Read Interval Type 3 Read IntervalType 8 Read Interval Type 7 Read IntervalTime Synchronization Interval Configuring the A164MODE Table A164MODE First DvcfNumber of Dvcf BECCO2200 DCA Configuring the A164DVCF Configuration Table Number of Data Records First UnitNumber of Units First Data RecordConfiguring the A164DTBL Configuration Table Point Number Table TypeData Value Appendix AMessages Logged by the BECO2200 DCA Fatal Error MessagesF103 Bad Cfgdca record counts, must be F100 Bad A164APPL record counts, must beF101 Bad A164PORT record counts, must be F102 Bad A164UNIT record counts, must beF105 Invalid SOE Overflow parameter F107 x WESDACy pnts configured, z requiredF106 Total # devices exceeds Unit size F111 Bad A164DVCF record counts, must be F108 x table creation errorF110 Fatal errors exist in configuration F109 Cannot find x database tableF123 Dvcf Record x, invalid Number of Units F120 Mode Record x, invalid First DvcfF121 Mode Record x, invalid Number of Dvcf F122 Dvcf Record x, invalid First UnitF125 Dvcf Record x, invalid Number of Type-Point F200 Error x on win openF201 Error x signaling A164-D-00 process F203 Error x creating A164-y-z exchangeF207 Unable to allocate buffers F204 Error x spawning A164-y-z processF205 Error x activating A164-y-z process F206 Process A164-x-y died while initializingE302 Port rec x, num of devices exceeds Unit Non-Fatal Error MessagesE300 Port rec x, invalid baud rate E301 Port rec x, invalid failures before offlineE305 Unit rec x, invalid unit type E303 Port rec x, configuration badE307 Unit rec x, configuration bad E304 Port rec x, invalid unit addressE308 Port rec x, num of devices cannot = E399 Non-fatal errors exist in configurationE400 Error x opening port y E401 Error x setting character portE405 Error x activating A164-y-z process E402 Error x setting SIO timersE403 Error x creating A164-y-z exchange E404 Error x spawning A164-y-z processE408 Unable to allocate polling list E407 Error x signalling A164-y-z processE409 Error x, invalid start signal from Spawner E406 Process A164-x-y died while initializingPSOS Interface Warnings I702 Port rec x, invalid RTS off time Information MessagesI700 Port rec x, invalid reply time-out I701 Port rec x, invalid RTS on timeI704 No Configuration deleting I703 Port rec x, invalid intercharacter timeoutI705 Port rec x, no polling required AO Operate Failed Output Request Return CodesDemand Scan Failed Do Operate FailedAscii Glossary of TermsRAM Menu-oriented software program that operates on a personal A164-0CG-1.00-2Restricted List of Acronyms and Abbreviations