GE BECCO2200 F100 Bad A164APPL record counts, must be, F101 Bad A164PORT record counts, must be

Page 42

	BECCO2200 DCA
GE Energy Services	Configuration Guide

F100: Bad A164APPL record counts, must be 1

Cause:

•The A164APPL configuration table contained a number of records not equal to one.

Remedy:

•Review the section on configuring the A164APPL table (Chapter 3:), and ensure that the table consists of only one record.

F101: Bad A164PORT record counts, must be > 0

Cause:

•The A164PORT configuration table contained a number of records less than one.

Remedy:

•Review the section on configuring the A164PORT (Chapter 4:), and ensure that the table consists of one or more records.

F102: Bad A164UNIT record counts, must be > 0

Cause:

•The A164UNIT contained a number of records less than one.

Remedy:

•Review the section on configuring the A164UNIT (Chapter 5:), and ensure that the table consists of one or more records.

F103: Bad CFG_DCA record counts, must be > 0

Cause:

•The CFG_DCA configuration table contained a number of records less than one.

Remedy:

•Review the section on configuring WIN for the BECO2200 DCA (Chapter 2:), and ensure that the table consists of one record for every DCA and DTA in the system.

•Review the WIN User’s Configuration Guide for more information on how to configure WIN.

F104: Invalid DCA index

Cause:

•The DCA Index configuration parameter in the A164APPL table specifies an invalid index into the WIN CFG_DCA table.

Remedy:

•Review the section on configuring WIN for the BECO2200 DCA (Chapter 2:), and ensure that the table consists of one record for every DCA and DTA in the system.

•Review the section on configuring the A164APPL table (Chapter 3:) and verify that the DCA Index parameter specifies a valid index into the WIN CFG_DCA table (the index is a zero based table offset).

A164-0CG-1.00-2Restricted

26	Full

Image 42

Contents Configuration Guide BECCO2200 DCATrademark Notices Table of Contents Configuring the A164MODE Table Configuring the A164DTBL Configuration Table BECCO2200 DCA List of Figures Viii List of Tables BECCO2200 DCA About this Guide Purpose of this GuideWho Should Use this Guide Additional Documentation Introduction to the Wesdac D20 RTU GEN-0003How this Guide is Organized Xiv Overview Xvi Configuration Tables BECO2200 DCA Configuration TablesConfiguration Sequence Configuring Win for the BECO2200 DCA Wesdac Point AllocationCounters Binary InputsBinary Outputs Analog InputsConfiguring the A164APPL Table General InformationDescription of Fields DCA Index Reply Buffer Size AdjustmentSOE Buffer Size Adjustment SOE Buffer Overflow OptionDevice Event Response Time BECCO2200 DCA Configuring the A164PORT Table BECO2200 DCA A164PORT Configuration TableBaud Rate Communication Port NameCommunication Port Parity RTS On TimeIntercharacter Timeout Remote Reply TimeoutRTS Off Time Failures Before Off-line Line Idle TimeRetries Before Failure Number of Devices on PortConfiguring the A164UNIT Table BECO2200 DCA A164UNIT Configuration TableRemote Address Unit TypeType 0 Read Interval Type 3 Read Interval Type 1 Read IntervalType 2 Read Interval Type 4 Read IntervalType 7 Read Interval Type 8 Read IntervalTime Synchronization Interval Configuring the A164MODE Table First Dvcf A164MODENumber of Dvcf BECCO2200 DCA Configuring the A164DVCF Configuration Table First Data Record First UnitNumber of Units Number of Data RecordsConfiguring the A164DTBL Configuration Table Table Type Point NumberData Value Fatal Error Messages Appendix AMessages Logged by the BECO2200 DCAF102 Bad A164UNIT record counts, must be F100 Bad A164APPL record counts, must beF101 Bad A164PORT record counts, must be F103 Bad Cfgdca record counts, must beF107 x WESDACy pnts configured, z required F105 Invalid SOE Overflow parameterF106 Total # devices exceeds Unit size F109 Cannot find x database table F108 x table creation errorF110 Fatal errors exist in configuration F111 Bad A164DVCF record counts, must beF122 Dvcf Record x, invalid First Unit F120 Mode Record x, invalid First DvcfF121 Mode Record x, invalid Number of Dvcf F123 Dvcf Record x, invalid Number of UnitsF203 Error x creating A164-y-z exchange F200 Error x on win openF201 Error x signaling A164-D-00 process F125 Dvcf Record x, invalid Number of Type-PointF206 Process A164-x-y died while initializing F204 Error x spawning A164-y-z processF205 Error x activating A164-y-z process F207 Unable to allocate buffersE301 Port rec x, invalid failures before offline Non-Fatal Error MessagesE300 Port rec x, invalid baud rate E302 Port rec x, num of devices exceeds UnitE304 Port rec x, invalid unit address E303 Port rec x, configuration badE307 Unit rec x, configuration bad E305 Unit rec x, invalid unit typeE401 Error x setting character port E399 Non-fatal errors exist in configurationE400 Error x opening port y E308 Port rec x, num of devices cannot =E404 Error x spawning A164-y-z process E402 Error x setting SIO timersE403 Error x creating A164-y-z exchange E405 Error x activating A164-y-z processE406 Process A164-x-y died while initializing E407 Error x signalling A164-y-z processE409 Error x, invalid start signal from Spawner E408 Unable to allocate polling listPSOS Interface Warnings I701 Port rec x, invalid RTS on time Information MessagesI700 Port rec x, invalid reply time-out I702 Port rec x, invalid RTS off timeI703 Port rec x, invalid intercharacter timeout I704 No Configuration deletingI705 Port rec x, no polling required Do Operate Failed Output Request Return CodesDemand Scan Failed AO Operate FailedGlossary of Terms AsciiRAM Menu-oriented software program that operates on a personal A164-0CG-1.00-2Restricted List of Acronyms and Abbreviations