GE BECCO2200 manual E308 Port rec x, num of devices cannot =, E400 Error x opening port y

Page 50

	BECCO2200 DCA
GE Energy Services	Configuration Guide

Remedy:

•Address all non-fatal errors preceding this message.

E308: PORT rec <x>, num of devices cannot = 0

Cause:

•The Number of Devices on Port parameter in record <x> of the A164PORT table is equal to zero.

Effect:

•Communication on this port will be unavailable.

Remedy:

•Review the section on configuring the A164PORT table (Chapter 4:), and verify that the Number of Devices on Port is correct.

E399: Non-fatal errors exist in configuration

Cause:

•The BECO2200 DCA encountered non-fatal error in its configuration.

Effect:

•The BECO2200 will be unable to communicate to some or all of the devices configured.

Remedy:

•Address all non-fatal error messages preceding this message.

E400: Error <x> opening port <y>

Cause:

•The BECO2200 DCA failed in its attempt to open the communication port <y>. The error code returned was <x>.

Effect:

•Communication to all devices configured for this port will be unavailable.

Remedy:

•Ensure that no other application is configured to use port <y>.

•Call the Customer Service department and report this error.

E401: Error <x> setting character port

Cause:

•The BECO2200 DCA failed in its attempt to set the communication port characteristics. The error code returned was <x>.

Effect:

•Communication to all devices configured for this port will be unavailable.

Remedy:

•Call the Customer Service department and report this error.

A164-0CG-1.00-2Restricted

34	Full

Image 50

Contents Configuration Guide BECCO2200 DCATrademark Notices Table of Contents Configuring the A164MODE Table Configuring the A164DTBL Configuration Table BECCO2200 DCA List of Figures Viii List of Tables BECCO2200 DCA Who Should Use this Guide About this GuidePurpose of this Guide Additional Documentation Introduction to the Wesdac D20 RTU GEN-0003How this Guide is Organized Xiv Overview Xvi Configuration Tables BECO2200 DCA Configuration TablesConfiguration Sequence Configuring Win for the BECO2200 DCA Wesdac Point AllocationCounters Binary InputsBinary Outputs Analog InputsDescription of Fields Configuring the A164APPL TableGeneral Information DCA Index Reply Buffer Size AdjustmentSOE Buffer Size Adjustment SOE Buffer Overflow OptionDevice Event Response Time BECCO2200 DCA Configuring the A164PORT Table BECO2200 DCA A164PORT Configuration TableBaud Rate Communication Port NameCommunication Port Parity RTS On TimeRTS Off Time Intercharacter TimeoutRemote Reply Timeout Failures Before Off-line Line Idle TimeRetries Before Failure Number of Devices on PortConfiguring the A164UNIT Table BECO2200 DCA A164UNIT Configuration TableType 0 Read Interval Remote AddressUnit Type Type 3 Read Interval Type 1 Read IntervalType 2 Read Interval Type 4 Read IntervalTime Synchronization Interval Type 7 Read IntervalType 8 Read Interval Configuring the A164MODE Table First Dvcf A164MODENumber of Dvcf BECCO2200 DCA Configuring the A164DVCF Configuration Table First Data Record First UnitNumber of Units Number of Data RecordsConfiguring the A164DTBL Configuration Table Data Value Table TypePoint Number Fatal Error Messages Appendix AMessages Logged by the BECO2200 DCAF102 Bad A164UNIT record counts, must be F100 Bad A164APPL record counts, must beF101 Bad A164PORT record counts, must be F103 Bad Cfgdca record counts, must beF106 Total # devices exceeds Unit size F107 x WESDACy pnts configured, z requiredF105 Invalid SOE Overflow parameter F109 Cannot find x database table F108 x table creation errorF110 Fatal errors exist in configuration F111 Bad A164DVCF record counts, must beF122 Dvcf Record x, invalid First Unit F120 Mode Record x, invalid First DvcfF121 Mode Record x, invalid Number of Dvcf F123 Dvcf Record x, invalid Number of UnitsF203 Error x creating A164-y-z exchange F200 Error x on win openF201 Error x signaling A164-D-00 process F125 Dvcf Record x, invalid Number of Type-PointF206 Process A164-x-y died while initializing F204 Error x spawning A164-y-z processF205 Error x activating A164-y-z process F207 Unable to allocate buffersE301 Port rec x, invalid failures before offline Non-Fatal Error MessagesE300 Port rec x, invalid baud rate E302 Port rec x, num of devices exceeds UnitE304 Port rec x, invalid unit address E303 Port rec x, configuration badE307 Unit rec x, configuration bad E305 Unit rec x, invalid unit typeE401 Error x setting character port E399 Non-fatal errors exist in configurationE400 Error x opening port y E308 Port rec x, num of devices cannot =E404 Error x spawning A164-y-z process E402 Error x setting SIO timersE403 Error x creating A164-y-z exchange E405 Error x activating A164-y-z processE406 Process A164-x-y died while initializing E407 Error x signalling A164-y-z processE409 Error x, invalid start signal from Spawner E408 Unable to allocate polling listPSOS Interface Warnings I701 Port rec x, invalid RTS on time Information MessagesI700 Port rec x, invalid reply time-out I702 Port rec x, invalid RTS off timeI705 Port rec x, no polling required I703 Port rec x, invalid intercharacter timeoutI704 No Configuration deleting Do Operate Failed Output Request Return CodesDemand Scan Failed AO Operate FailedGlossary of Terms AsciiRAM Menu-oriented software program that operates on a personal A164-0CG-1.00-2Restricted List of Acronyms and Abbreviations