GE BECCO2200 manual First Unit, Number of Units, First Data Record, Number of Data Records

Page 38

	BECCO2200 DCA
GE Energy Services	Configuration Guide

7.2.1 First Unit

This parameter specifies the first unit to which this set of data records will be downloaded. The First Unit must specify a valid range of records in the A164UNIT.

7.2.2 Number of Units

This parameter specifies the number of units to which this set of data records will be downloaded. The Number of Units must specify a valid range of records in the A164UNIT.

7.2.3 First Data Record

This parameter specifies the first data record of this set. The First Data Record must specify a valid range of records in the A164DTBL table.

7.2.4 Number of Data Records

This parameter specifies the number of data records contained in this set. The Number of Data Records must specify a valid range of records in the A164DTBL table.

A164-0CG-1.00-2Restricted

22	Full

Image 38

Contents Configuration Guide BECCO2200 DCATrademark Notices Table of Contents Configuring the A164MODE Table Configuring the A164DTBL Configuration Table BECCO2200 DCA List of Figures Viii List of Tables BECCO2200 DCA Who Should Use this Guide About this GuidePurpose of this Guide Additional Documentation Introduction to the Wesdac D20 RTU GEN-0003How this Guide is Organized Xiv Overview Xvi Configuration Tables BECO2200 DCA Configuration TablesConfiguration Sequence Configuring Win for the BECO2200 DCA Wesdac Point AllocationCounters Binary InputsBinary Outputs Analog InputsDescription of Fields Configuring the A164APPL TableGeneral Information DCA Index Reply Buffer Size AdjustmentSOE Buffer Size Adjustment SOE Buffer Overflow OptionDevice Event Response Time BECCO2200 DCA Configuring the A164PORT Table BECO2200 DCA A164PORT Configuration TableBaud Rate Communication Port NameCommunication Port Parity RTS On TimeRTS Off Time Intercharacter TimeoutRemote Reply Timeout Failures Before Off-line Line Idle TimeRetries Before Failure Number of Devices on PortConfiguring the A164UNIT Table BECO2200 DCA A164UNIT Configuration TableType 0 Read Interval Remote AddressUnit Type Type 3 Read Interval Type 1 Read IntervalType 2 Read Interval Type 4 Read IntervalTime Synchronization Interval Type 7 Read IntervalType 8 Read Interval Configuring the A164MODE Table First Dvcf A164MODENumber of Dvcf BECCO2200 DCA Configuring the A164DVCF Configuration Table First Data Record First UnitNumber of Units Number of Data RecordsConfiguring the A164DTBL Configuration Table Data Value Table TypePoint Number Fatal Error Messages Appendix AMessages Logged by the BECO2200 DCAF102 Bad A164UNIT record counts, must be F100 Bad A164APPL record counts, must beF101 Bad A164PORT record counts, must be F103 Bad Cfgdca record counts, must beF106 Total # devices exceeds Unit size F107 x WESDACy pnts configured, z requiredF105 Invalid SOE Overflow parameter F109 Cannot find x database table F108 x table creation errorF110 Fatal errors exist in configuration F111 Bad A164DVCF record counts, must beF122 Dvcf Record x, invalid First Unit F120 Mode Record x, invalid First DvcfF121 Mode Record x, invalid Number of Dvcf F123 Dvcf Record x, invalid Number of UnitsF203 Error x creating A164-y-z exchange F200 Error x on win openF201 Error x signaling A164-D-00 process F125 Dvcf Record x, invalid Number of Type-PointF206 Process A164-x-y died while initializing F204 Error x spawning A164-y-z processF205 Error x activating A164-y-z process F207 Unable to allocate buffersE301 Port rec x, invalid failures before offline Non-Fatal Error MessagesE300 Port rec x, invalid baud rate E302 Port rec x, num of devices exceeds UnitE304 Port rec x, invalid unit address E303 Port rec x, configuration badE307 Unit rec x, configuration bad E305 Unit rec x, invalid unit typeE401 Error x setting character port E399 Non-fatal errors exist in configurationE400 Error x opening port y E308 Port rec x, num of devices cannot =E404 Error x spawning A164-y-z process E402 Error x setting SIO timersE403 Error x creating A164-y-z exchange E405 Error x activating A164-y-z processE406 Process A164-x-y died while initializing E407 Error x signalling A164-y-z processE409 Error x, invalid start signal from Spawner E408 Unable to allocate polling listPSOS Interface Warnings I701 Port rec x, invalid RTS on time Information MessagesI700 Port rec x, invalid reply time-out I702 Port rec x, invalid RTS off timeI705 Port rec x, no polling required I703 Port rec x, invalid intercharacter timeoutI704 No Configuration deleting Do Operate Failed Output Request Return CodesDemand Scan Failed AO Operate FailedGlossary of Terms AsciiRAM Menu-oriented software program that operates on a personal A164-0CG-1.00-2Restricted List of Acronyms and Abbreviations