Extron electronic IPL T PCS4i manual None and Not Set thresholds, Standby

Page 17

SET REFERENCE

STANDBY FULL

Setting the Standby power threshold 1. Power off the attached device.

2. Press and hold the Standby button (shown at right).

3. While holding down the Standby button, press and release the receptacle button for the same device for which you set the Full threshold. The Standby LED for the selected receptacle blinks twice and remains lit.

1

F

Standby

LED

S

Receptacle Button

4.Release the Standby button.

5.Repeat steps 1 through 9 for any other receptacles to which you have connected devices to be controlled through the PCS4.

NOTE: Settings that are made via the front panel for power output receptacles

and reference thresholds take approximately two minutes to be stored in

memory. If you recycle power too soon after settings have been made, the settings are lost.

These threshold settings are preserved if the PCS4 AC power is recycled or if power is removed from an attached device. For example:

If the receptacle

is set to...

And the power level...

The receptacle...

	Full	drops below the stored threshold	F (Full) led shuts off, and the
	Full	drops below the stored threshold	S (Standby) LED lights.
			S (Standby) LED lights.
		drops below the stored Standby	S LED shuts off.
	Standby	threshold	S LED shuts off.
	Standby	threshold
		exceeds the stored Standby threshold	F LED lights.

To indicate that the configuration has been saved, both the Standby LED and the Full LED light and remain lit when those thresholds are selected.

None and Not Set thresholds

When a Full or Standby reference threshold has been set for a receptacle at some time, and neither threshold is detected, a threshold status of None appears on the web page or can be the response to SIS queries. None also appears if the receptacle is powered off. The None threshold is a state that is detected; it cannot be set manually.

If a receptacle has never been set to a Full or Standby reference threshold, its threshold status is shown as Not Set on the web page and in response to SIS queries. Not Set is the default setting for reference thresholds.

IPL T PCS4 • Front Panel Features and Operation 11

Image 17

Contents IPL T PCS4i IPL T PCS4Safety Instructions English FCC Class a Notice Notifications Software CommandsConventions Used in this Guide Contents IPL T PCS4 Contents Introduction FeaturesAbout this Guide About the IPL T PCS4IPL T PCS4 Application DiagramsConnection Diagram for IPL T PCS4i Installation Overview Installation Rear PanelsIPL T PCS4i Rear Panel 220 VAC Rear PanelsConnecting the Devices Setting Up the LAN PortConfiguring the LAN Port LAN Port CablingIPL T PCS4 Installation and Rear Panel Front Panel Features Front Panel Features OperationSetting Power Level Reference Thresholds Setting Up the System Using the Front PanelSetting Up Power Control Setting the Full power threshold Standby If the receptacle Is set to Power level Receptacle FullNone and Not Set thresholds LED lit Group Red power LED lit Group Front panel Security Lockout Executive ModeGrouping Receptacles Clearing thresholdsMode Resetting the UnitActivation ResultHold the Reset button in until the Power LED blinks once Setting Up the Computer Using ARP Configuration ControlConfiguring the Hardware ARP-S Command Screen Screen Showing the Ping Command Setting Up the Computer Using a Web BrowserSetting up the computer for IP communication Subnet mask Default gateway Blank or Example of a Default System Settings Configuring the IPL T PCS4 using a web browserPassword Prompt Window Using the Embedded Web PagesSystem Status Web Viewing the System StatusIP settings ConfigurationSpecifying system settings Date and time settings Removing passwords Assigning passwordsTo assign passwords Mail Alerts Screen Upper Portion Entering e-mail addresses for alertsManaging receptacles Upgrading firmwareGrouping receptacles Switching power to receptacles on and offMonitoring Settings section Monitoring the receptacles and setting the alarmAlarm Relay Settings section Scheduling an individual receptacle Scheduling power to receptaclesAll receptacles on and off Scheduling receptacles by day of the weekFile Management One receptacle, power on or offOther file management functions Uploading files to the webAdding a directory Query Strings Custom Web PagesServer Side Includes SSIs Code example Example of a Query String CommandBrowser View of Previous Html Source Code URL EncodingCharacters Hex Dec Reserved charactersUnsafe characters Custom Web Pages Device Power ControlAccessing and Using Telnet Port Power Connections TroubleshootingNetwork Connections Successful Ping Command ResponseDownloading Global Configurator Software Messages Initiated by the IPL T PCS4 SIS Programming ControlHost-to-Interface Communication Error Response References Password InformationError Responses Telnet Web Browser Using the Command and Response TableExample Symbol DefinitionsX5@ X71 Power Receptacle Monitoring and Alarm Functions Command and Response Table for SIS CommandsWeb Browser-specific Commands Set GMT offset24 View GMT offset Password and Security SettingsDirectory Commands Below Telnet text responses Reference Material SpecificationsEthernet control interface AC control interfaceGeneral Alarm relay controlMounting the IPL T PCS4 Interface Part Numbers and AccessoriesMounting the IPL T PCS4 on a Rack Shelf Rack mounting procedureMounting the IPL T PCS4 under Furniture Under-desk Mounting10/100Base-T GlossaryDriver Power level reference threshold Subnet Europe, Africa, and the Middle China East USA, Canada, South America Japan Central AmericaAsia Middle East Europe

Related manuals

Manual 2 pages 35.37 Kb