Extron electronic IPL T PCS4i manual Upgrading firmware, Managing receptacles

Page 33

8.Click the Save button beside the file name that you entered. The e-mail alert information is saved on the PCS4, and the Save button becomes Edit again.

9.Repeat steps 5 through 8 for each e-mail recipient address that you want to add or edit.

Upgrading firmware

The Firmware Upgrade screen lets you browse to locate and upload a new version of firmware for your unit. The uploaded file must have the file extension .S19.

NOTE: The PCS4 .S19 file is not the same as the .S19 files of other products and is not interchangeable with the firmware upgrade files of any other product.

Figure 17. Firmware Upgrade Screen

To upload a new version of firmware:

1.On the side-bar menu of the Configuration tab, click Firmware Upgrade. The

Firmware Upgrade screen is displayed, showing the version of firmware that is currently loaded.

2.Click Browse to open a Windows file selection window.

3.On the file selection window, locate the new firmware version file on your server and double-click it. (Firmware files must have the extension .S19.) The firmware file name and path are displayed in the Current Firmware Version section on the Firmware Upgrade screen.

4.Click Upload. When the firmware upgrade is complete, the Power LED on the unit blinks three times.

NOTE: If you attempt to upload a file with an extension other than .S19, the PCS4

recognizes it as invalid and ignores it, reverting to the factory installed firmware version.

Managing receptacles

On the Switching/Grouping screen, you can switch power on and off to each individual receptacle, group the receptacles together, and power each group on and off. You can also view the threshold settings (Full, Standby, None, or Not Set) indicating the device power level at which the alarm relay will be activated for each receptacle.

NOTE: You cannot set the reference thresholds on this screen. This can be done only

from the IPL T PCS4 front panel or via SIS commands. See “Setting Power

Level Reference Thresholds” in the “Front Panel Features and Operation”

section or the “SIS Programming and Control” section for information on setting thresholds from the front panel or via SIS commands.

IPL T PCS4 • HTML Configuration and Control 27

Image 33

Contents IPL T PCS4i IPL T PCS4Safety Instructions English FCC Class a Notice Software Commands Conventions Used in this GuideNotifications Contents IPL T PCS4 Contents Introduction FeaturesAbout this Guide About the IPL T PCS4IPL T PCS4 Application DiagramsConnection Diagram for IPL T PCS4i Installation Overview Installation Rear PanelsIPL T PCS4i Rear Panel 220 VAC Rear PanelsConnecting the Devices Setting Up the LAN PortConfiguring the LAN Port LAN Port CablingIPL T PCS4 Installation and Rear Panel Front Panel Features Front Panel Features OperationSetting Up the System Using the Front Panel Setting Up Power ControlSetting Power Level Reference Thresholds Setting the Full power threshold If the receptacle Is set to Power level Receptacle Full None and Not Set thresholdsStandby LED lit Group Red power LED lit Group Front panel Security Lockout Executive ModeGrouping Receptacles Clearing thresholdsMode Resetting the UnitActivation ResultHold the Reset button in until the Power LED blinks once Configuration Control Configuring the HardwareSetting Up the Computer Using ARP ARP-S Command Screen Screen Showing the Ping Command Setting Up the Computer Using a Web BrowserSetting up the computer for IP communication Subnet mask Default gateway Blank or Example of a Default System Settings Configuring the IPL T PCS4 using a web browserPassword Prompt Window Using the Embedded Web PagesSystem Status Web Viewing the System StatusConfiguration Specifying system settingsIP settings Date and time settings Assigning passwords To assign passwordsRemoving passwords Mail Alerts Screen Upper Portion Entering e-mail addresses for alertsManaging receptacles Upgrading firmwareGrouping receptacles Switching power to receptacles on and offMonitoring Settings section Monitoring the receptacles and setting the alarmAlarm Relay Settings section Scheduling an individual receptacle Scheduling power to receptaclesAll receptacles on and off Scheduling receptacles by day of the weekFile Management One receptacle, power on or offUploading files to the web Adding a directoryOther file management functions Custom Web Pages Server Side Includes SSIsQuery Strings Code example Example of a Query String CommandBrowser View of Previous Html Source Code URL EncodingReserved characters Unsafe charactersCharacters Hex Dec Device Power Control Accessing and Using Telnet PortCustom Web Pages Power Connections TroubleshootingNetwork Connections Successful Ping Command ResponseDownloading Global Configurator Software SIS Programming Control Host-to-Interface CommunicationMessages Initiated by the IPL T PCS4 Password Information Error ResponsesError Response References Telnet Web Browser Using the Command and Response TableExample Symbol DefinitionsX5@ X71 Power Receptacle Monitoring and Alarm Functions Command and Response Table for SIS CommandsWeb Browser-specific Commands Set GMT offset24 View GMT offset Password and Security SettingsDirectory Commands Below Telnet text responses Reference Material SpecificationsEthernet control interface AC control interfaceGeneral Alarm relay controlMounting the IPL T PCS4 Interface Part Numbers and AccessoriesMounting the IPL T PCS4 on a Rack Shelf Rack mounting procedureMounting the IPL T PCS4 under Furniture Under-desk Mounting10/100Base-T GlossaryDriver Power level reference threshold Subnet Europe, Africa, and the Middle China East USA, Canada, South America Japan Central AmericaAsia Middle East Europe

Related manuals

Manual 2 pages 35.37 Kb