Extron electronic IPL T PCS4i manual Alarm Relay Settings section

Page 36

•Activate Relay: Select this check box to specify that the relay alarm will sound (activate) if the selected condition is met. If this box is not selected, any changes you make to the alarm relay settings are ignored.

•Alarm status: Indicates whether or not the PCS4 has detected the condition that is being monitored. This column can display the following:

•Inactive — Appears when the receptacle is not being monitored, or the condition being monitored has not been detected.

•Active — Appears in red when the PCS4 detects the condition for which the receptacle is being monitored. In addition, a Silence button appears at the right of the status, and a pulsing red light icon appears by the number of the receptacle for which the condition was met.

•Silenced — Appears in red when you click the Silence button to clear the monitored condition. In addition, the pulsing red light icon is replaced by an exclamation point icon (!).

To reset the alarm status, deselect and reselect the Enable check box for the receptacle being monitored, then click Submit. The Alarm Status column displays inactive again and the ! icon is removed.

Alarm Relay Settings section

In this section, you can configure the alarm relay by making selections in the following fields.

NOTE: The Activate Relay check box must be selected for these settings to take effect.

•Initial State: Select Open or Closed from the pull-down menu for the initial state of the alarm relay. (The default is Open.)

•Action: From the pull-down menu, select the way in which the alarm will respond when activated. This depends on the relay setting in the Initial State column.

•Activate — Steady tone if the initial state of the relay is set to On. If the initial state is set to Off, this option turns the alarm relay off.

•Pulse — Alarm turns on for the selected duration of seconds, then stops.

•Oscillate — The alarm is on for a specified duration of seconds, then off for a specified period, producing an intermittent tone.

•Duration (seconds): From the pull-down menus, select the length (in seconds) of the alarm tone action selected in the Action section (Pulse or Oscillate only).

•For Pulse, you can set the length of the single tone (On menu).

•For Oscillate, you can set the length of the repeating tone (On menu) and the amount of time between tones (Off menu).

•Cancel Alarm when: From one of the following menus, select the condition that will stop the alarm tone.

•Condition Changes — Select the type of change in conditions that will make the alarm stop sounding. (Selecting Manual specifies that the tone will not stop without user intervention via the front panel, the powered device, or SIS commands.)

•Duration — Select the number of minutes the alarm will continue to sound before it shuts off.

IPL T PCS4 • HTML Configuration and Control 30

Page 35 Page 37
Image 36
Page 35 Page 37
Contents IPL T PCS4 IPL T PCS4iSafety Instructions English FCC Class a Notice Software Commands Conventions Used in this GuideNotifications Contents IPL T PCS4 Contents Features IntroductionAbout this Guide About the IPL T PCS4Application Diagrams IPL T PCS4Connection Diagram for IPL T PCS4i Installation Rear Panels Installation OverviewRear Panels IPL T PCS4i Rear Panel 220 VACSetting Up the LAN Port Connecting the DevicesConfiguring the LAN Port LAN Port CablingIPL T PCS4 Installation and Rear Panel Front Panel Features Operation Front Panel FeaturesSetting Up the System Using the Front Panel Setting Up Power ControlSetting Power Level Reference Thresholds Setting the Full power threshold If the receptacle Is set to Power level Receptacle Full None and Not Set thresholdsStandby Front panel Security Lockout Executive Mode LED lit Group Red power LED lit GroupGrouping Receptacles Clearing thresholdsResetting the Unit ModeActivation ResultHold the Reset button in until the Power LED blinks once Configuration Control Configuring the HardwareSetting Up the Computer Using ARP ARP-S Command Screen Setting Up the Computer Using a Web Browser Screen Showing the Ping CommandSetting up the computer for IP communication Subnet mask Default gateway Blank or Configuring the IPL T PCS4 using a web browser Example of a Default System SettingsUsing the Embedded Web Pages Password Prompt WindowViewing the System Status System Status WebConfiguration Specifying system settingsIP settings Date and time settings Assigning passwords To assign passwordsRemoving passwords Entering e-mail addresses for alerts Mail Alerts Screen Upper PortionUpgrading firmware Managing receptaclesSwitching power to receptacles on and off Grouping receptaclesMonitoring the receptacles and setting the alarm Monitoring Settings sectionAlarm Relay Settings section Scheduling power to receptacles Scheduling an individual receptacleScheduling receptacles by day of the week All receptacles on and offOne receptacle, power on or off File ManagementUploading files to the web Adding a directoryOther file management functions Custom Web Pages Server Side Includes SSIsQuery Strings Example of a Query String Command Code exampleURL Encoding Browser View of Previous Html Source CodeReserved characters Unsafe charactersCharacters Hex Dec Device Power Control Accessing and Using Telnet PortCustom Web Pages Troubleshooting Power ConnectionsSuccessful Ping Command Response Network ConnectionsDownloading Global Configurator Software SIS Programming Control Host-to-Interface CommunicationMessages Initiated by the IPL T PCS4 Password Information Error ResponsesError Response References Using the Command and Response Table Telnet Web BrowserSymbol Definitions ExampleX5@ X71 Command and Response Table for SIS Commands Power Receptacle Monitoring and Alarm FunctionsWeb Browser-specific Commands Password and Security Settings Set GMT offset24 View GMT offsetDirectory Commands Below Telnet text responses Specifications Reference MaterialEthernet control interface AC control interfaceAlarm relay control GeneralPart Numbers and Accessories Mounting the IPL T PCS4 InterfaceRack mounting procedure Mounting the IPL T PCS4 on a Rack ShelfUnder-desk Mounting Mounting the IPL T PCS4 under FurnitureGlossary 10/100Base-TDriver Power level reference threshold Subnet USA, Canada, South America Japan Central America Europe, Africa, and the Middle China EastAsia Middle East Europe
Related manuals
Manual 2 pages 35.37 Kb
Top Page Image Contents