Extron electronic IPL T PCS4i manual ARP-S Command Screen

Page 22

3.If the PCS4 has never been configured and is still set for factory defaults, skip to step 4. If not, perform a mode 4 system reset to restore the factory-set values (see “Resetting the Unit” in the “Front Panel Features and Operations” section for the resetting procedure).

NOTE: The PCS4 must be configured with the factory default IP address

(192.168.254.254) before you execute the ARP command, as described below.

4.On the computer, access the command prompt, then enter arp -s, the desired new IP address for the PCS4, a space, and finally the PCS4 MAC address (taken from the label on the rear panel). For example:

arp -s 10.13.170.15 00-05-A6-00-0A-90

A space must separate arp from the hyphen (-).

Figure 9. ARP-S Command Screen

NOTE: After the arp -scommand is issued, the PCS4 changes to the new address and starts responding to ping requests, as described in the next step.

5.To verify that the new address has been set, execute a ping command by entering ping, followed by the new IP address, at the command prompt.

NOTE: Ping is a utility or diagnostic tool that tests network connections. It is used to

determine if the host has an operating connection and is able to exchange information with another host.

Example:

ping 10.13.170.15

Ping is a utility or diagnostic tool that tests network connections. It is used to determine if the host has an operating connection and is able to exchange information with another host.

IPL T PCS4 • HTML Configuration and Control 16

Image 22

Contents IPL T PCS4 IPL T PCS4iSafety Instructions English FCC Class a Notice Conventions Used in this Guide Software CommandsNotifications Contents IPL T PCS4 Contents About this Guide FeaturesIntroduction About the IPL T PCS4Application Diagrams IPL T PCS4Connection Diagram for IPL T PCS4i Installation Rear Panels Installation OverviewRear Panels IPL T PCS4i Rear Panel 220 VACConfiguring the LAN Port Setting Up the LAN PortConnecting the Devices LAN Port CablingIPL T PCS4 Installation and Rear Panel Front Panel Features Operation Front Panel FeaturesSetting Up Power Control Setting Up the System Using the Front PanelSetting Power Level Reference Thresholds Setting the Full power threshold None and Not Set thresholds If the receptacle Is set to Power level Receptacle FullStandby Grouping Receptacles Front panel Security Lockout Executive ModeLED lit Group Red power LED lit Group Clearing thresholdsActivation Resetting the UnitMode ResultHold the Reset button in until the Power LED blinks once Configuring the Hardware Configuration ControlSetting Up the Computer Using ARP ARP-S Command Screen Setting Up the Computer Using a Web Browser Screen Showing the Ping CommandSetting up the computer for IP communication Subnet mask Default gateway Blank or Configuring the IPL T PCS4 using a web browser Example of a Default System SettingsUsing the Embedded Web Pages Password Prompt WindowViewing the System Status System Status WebSpecifying system settings ConfigurationIP settings Date and time settings To assign passwords Assigning passwordsRemoving passwords Entering e-mail addresses for alerts Mail Alerts Screen Upper PortionUpgrading firmware Managing receptaclesSwitching power to receptacles on and off Grouping receptaclesMonitoring the receptacles and setting the alarm Monitoring Settings sectionAlarm Relay Settings section Scheduling power to receptacles Scheduling an individual receptacleScheduling receptacles by day of the week All receptacles on and offOne receptacle, power on or off File ManagementAdding a directory Uploading files to the webOther file management functions Server Side Includes SSIs Custom Web PagesQuery Strings Example of a Query String Command Code exampleURL Encoding Browser View of Previous Html Source CodeUnsafe characters Reserved charactersCharacters Hex Dec Accessing and Using Telnet Port Device Power ControlCustom Web Pages Troubleshooting Power ConnectionsSuccessful Ping Command Response Network ConnectionsDownloading Global Configurator Software Host-to-Interface Communication SIS Programming ControlMessages Initiated by the IPL T PCS4 Error Responses Password InformationError Response References Using the Command and Response Table Telnet Web BrowserSymbol Definitions ExampleX5@ X71 Command and Response Table for SIS Commands Power Receptacle Monitoring and Alarm FunctionsWeb Browser-specific Commands Password and Security Settings Set GMT offset24 View GMT offsetDirectory Commands Below Telnet text responses Ethernet control interface SpecificationsReference Material AC control interfaceAlarm relay control GeneralPart Numbers and Accessories Mounting the IPL T PCS4 InterfaceRack mounting procedure Mounting the IPL T PCS4 on a Rack ShelfUnder-desk Mounting Mounting the IPL T PCS4 under FurnitureGlossary 10/100Base-TDriver Power level reference threshold Subnet Asia Middle East USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Europe

Related manuals

Manual 2 pages 35.37 Kb