Foundry Networks FGS624P manual Installation Precautions, General Precautions, Lifting Precautions

Page 25

 

 

Installing the FastIron GS Chassis

 

Table 3.1: Summary of Installation Tasks (Continued)

 

 

 

Task

Task

Where to Find More Information

No.

 

 

 

 

 

10

Once you power on the device and assign IP addresses,

“Connecting Network Devices” on page 4-4

 

the system is ready to accept network equipment.

 

 

 

 

11

Test IP connectivity by pinging other devices and tracing

“Testing Connectivity” on page 4-6

 

routes.

 

 

 

 

12

Continue configuration using the CLI or the Web

Foundry FastIron Configuration Guide

 

management interface. You also can use IronView Network

 

 

Manager to manage the device. See the Foundry IronView

 

 

Network Management User’s Guide for information.

 

 

 

 

13

Secure access to the device.

Foundry FastIron Configuration Guide.

 

 

 

Installation Precautions

Follow these precautions when installing a Foundry device.

General Precautions

WARNING:

All fiber-optic interfaces use Class 1 lasers.

 

 

 

 

CAUTION:

Do not install the device in an environment where the operating ambient temperature might exceed

40o C (104o F).

 

 

CAUTION:

Make sure the air flow around the front, sides, and back of the device is not restricted.

 

 

 

 

CAUTION:

Never leave tools inside the chassis.

 

 

Lifting Precautions

WARNING: Make sure the rack or cabinet housing the device is adequately secured to prevent it from becoming unstable or falling over.

WARNING: Do not use the handles on the power supply units to lift or carry a Foundry device.

WARNING: Mount the devices you install in a rack or cabinet as low as possible. Place the heaviest device at the bottom and progressively place lighter devices above.

September 2007

© 2007 Foundry Networks, Inc.

3 - 3

Image 25
Contents FGS Release Page Contents Hecking C Onnectivity Hardware Specifications Egulatory S Tatements Introduction Chapter About This GuideWhat’s Included in This Edition? AudienceWarranty Coverage How to Get HelpRelated Publications Product Overview Chapter Product OverviewHardware Features Software FeaturesFGS624P and FGS624P-POE FGS648P and FGS648P-POE FGS624XGP and FGS624XGP-POEShows the FGS648P and FGS648P-POE Control FeaturesOptional 2-port 10-GbE Module port 49 Serial Management Interface Console PortNetwork Interfaces Reset ButtonNetwork Interfaces Show Media Description Port 10-GbE Module 10/100/1000 Mbps PortsPort 10-GbE Hybrid Interface Module Release Port CX4 Module Release10GbE XFP Transceiver FGS624XGP Models Only CX4 10Gbps XFP Transceiver 10GbE XG and CX4 ModuleLEDs LEDs for Network Interfaces and Power SuppliesPosition State Meaning 10/100/1000 Copper Port LEDs 100/1000 Fiber Port LEDsPosition State Meaning Power Supply LEDsGbps Port LEDs POE Port LEDsFiber Optic Modules Power SuppliesPosition State Meaning Stacking LEDs Cooling System and Fans Power Specifications for POESeptember Package Contents Chapter Installing the FastIron GS ChassisUnpacking a System General RequirementsSummary of Installation Tasks Where to Find More Information Summary of Installation TasksGeneral Precautions Installation PrecautionsLifting Precautions Summary of Installation TasksPower Supply Precautions Installing an Additional Power Supply Preparing the Installation SiteCabling Infrastructure Installation Location Power supply locking screw Latches Installing an AC Power SupplyRetaining Bale AC Power Cord Installing a DC Power Supply Ground screw Negative terminal screw Ground Desktop Installation Installing the DeviceRack Mount Installation Attaching the Short Mounting Brackets Installing the Brackets and Mounting the Device Wall Mount InstallationInstall top screws Install device Powering On the SystemVerifying Proper Operation Powering Off the SystemLEDs for Power Observing the Power Status LEDsAttaching a PC or Terminal FastIron FastIron-PREM DB-9 to DB-9 Assigning Permanent Passwords Chapter Connecting Network Devices Checking ConnectivityRecovering from a Lost Password Devices Running Layer 2 Software Configuring IP AddressesCable Specifications Connecting Network DevicesConnecting to Ethernet or Fast Ethernet Hubs Connecting a Network Device to a Fiber Port Connecting to Workstations, Servers, or RoutersInstalling a Fiber Optic Module Automatic MDI/MDIX DetectionCleaning the Fiber-Optic Connectors Testing ConnectivityPinging an IP Address Cabling a Fiber Optic ModuleNetwork Connection-Related LED States Observing LEDsDesired Meaning Abnormal Meaning/Action State Using Virtual Cable Testing to Diagnose a Cable Troubleshooting Network ConnectionsConfiguration Notes Command SyntaxThis Line Viewing the Results of the Cable AnalysisCable Statistics Displays September Using the Temperature Sensor Managing Temperature SettingsDisplaying the Temperature Chapter Managing the FastIron GS ChassisChanging the Temperature Warning Level Displaying Temperature MessagesDisplaying Management Module CPU Usage Changing the Chassis Temperature Polling IntervalRemoving MAC Address Entries September Chassis Specifications Chapter Hardware SpecificationsPower Supply Specifications Physical Dimensions and Weight Chassis SpecificationsEnvironmental Considerations Storage EnvironmentRegulatory Compliance CoolingChassis Regulatory Compliance Description Certifications Mean Time Between Failure Power Source InterruptionsPower Supply Draw Specifications Model Typical Maximum Power Draw SpecificationsSerial Console Port Pinouts Pinouts and Signalling10/100 and Gigabit Port Pinouts Lists the pin assignment and signalling for 10/100/100 portsLC connector 62.5/125 200 For SFP module Power Cords Power Supply SpecificationsWarranty LC connector 1530.33 Up to For XFP module 1561.42 nm 80 kmKey features 10 Maximum Power Supply Consumption for FGS Models FGS624 Power Supply ConsumptionFGS648 11 Input Connector for Power Supplies Input Connector and PlugPower Supply Input Connector Properties 13 Safety Warning Labels on Power Supplies Safety WarningsOutput Specifications Electrical SpecificationsReplacing a Power Supply Hardware Maintenance ScheduleChapter Maintaining the FastIron GS Hardware Determining Which Power Supply Failed Installation Precautions and WarningsAC Power Supplies Locking screw Removing an AC Power SupplyInstalling an AC Power Supply DC Power Supplies Shows a front view of the DC power supply Removing a DC Power SupplyInstalling a DC Power Supply Ground Installing a 2-port 10-GbE Module Installing or Replacing a 2-port 10-GbE ModuleRemoving a 2-port 10-GbE Module Installing a 2-port 10-GbE Module Installing or Replacing a POE Daughter CardRemoving the Screws for the Top Cover Disassembling the ChassisRemoving the Top Cover Installing a POE Daughter CardPOE Daughter Card POE Daughter Cards Re-assembling the ChassisRemoving a Fiber Optic Module Replacing a Fiber Optic ModuleInstalling a New Fiber Optic Module Cleaning the Fiber-Optic ConnectorsCabling a Fiber Optic Module Status Value Description Digital Optical MonitoringNo optical-monitor alarm interval CLI CommandsSupported Media Show optic port/slotnumberIndustry Canada Statement Appendix a Regulatory StatementsEurope and Australia JapanEnglish Translation of above statement Appendix B Foundry Networks, Inc Page Foundry Networks, Inc Page September Page September