Foundry Networks FGS648P-POE, FGS624P-POE, FGS624XGP-POE manual Retaining Bale AC Power Cord

Page 29

Installing the FastIron GS Chassis

4.With one hand, hold the bar on the front panel of the power supply. With the other hand, support the underside of the power supply, and insert the power supply into the empty power supply slot. Press until the supply is completely in the slot, so that the connectors on the back of the supply fully engage with the pins on the power backplane.

CAUTION: Make sure you insert the power supply right-side up. It is possible to insert the supply upside down, although the supply will not engage with the power backplane when upside down. The power supply is right-side up when the power connector is on the left and the fan vent is on the right.

5.Press the two latches near the edges of the supply outward to lock the supply in place.

6.Replace the power supply locking screw.

7.Install the power cord, as shown below.

Retaining Bale

AC Power Cord

September 2007

© 2007 Foundry Networks, Inc.

3 - 7

Image 29

Contents FGS Release Page Contents Hecking C Onnectivity Hardware Specifications Egulatory S Tatements Introduction Chapter About This GuideWhat’s Included in This Edition? AudienceRelated Publications How to Get HelpWarranty Coverage Product Overview Chapter Product OverviewFGS624P and FGS624P-POE Software FeaturesHardware Features FGS648P and FGS648P-POE FGS624XGP and FGS624XGP-POEShows the FGS648P and FGS648P-POE Control FeaturesOptional 2-port 10-GbE Module port 49 Serial Management Interface Console PortNetwork Interfaces Show Media Description Reset ButtonNetwork Interfaces Port 10-GbE Module 10/100/1000 Mbps Ports10GbE XFP Transceiver FGS624XGP Models Only Port CX4 Module ReleasePort 10-GbE Hybrid Interface Module Release CX4 10Gbps XFP Transceiver 10GbE XG and CX4 ModuleLEDs LEDs for Network Interfaces and Power SuppliesPosition State Meaning 10/100/1000 Copper Port LEDs 100/1000 Fiber Port LEDsPosition State Meaning Power Supply LEDsGbps Port LEDs POE Port LEDsPosition State Meaning Stacking LEDs Power SuppliesFiber Optic Modules Cooling System and Fans Power Specifications for POESeptember Package Contents Chapter Installing the FastIron GS ChassisUnpacking a System General RequirementsSummary of Installation Tasks Where to Find More Information Summary of Installation TasksGeneral Precautions Installation PrecautionsLifting Precautions Summary of Installation TasksPower Supply Precautions Cabling Infrastructure Installation Location Preparing the Installation SiteInstalling an Additional Power Supply Power supply locking screw Latches Installing an AC Power SupplyRetaining Bale AC Power Cord Installing a DC Power Supply Ground screw Negative terminal screw Ground Rack Mount Installation Installing the DeviceDesktop Installation Attaching the Short Mounting Brackets Installing the Brackets and Mounting the Device Wall Mount InstallationInstall top screws Install device Powering On the SystemVerifying Proper Operation Powering Off the SystemAttaching a PC or Terminal Observing the Power Status LEDsLEDs for Power FastIron FastIron-PREM DB-9 to DB-9 Assigning Permanent Passwords Chapter Connecting Network Devices Checking ConnectivityRecovering from a Lost Password Devices Running Layer 2 Software Configuring IP AddressesConnecting to Ethernet or Fast Ethernet Hubs Connecting Network DevicesCable Specifications Connecting a Network Device to a Fiber Port Connecting to Workstations, Servers, or RoutersInstalling a Fiber Optic Module Automatic MDI/MDIX DetectionCleaning the Fiber-Optic Connectors Testing ConnectivityPinging an IP Address Cabling a Fiber Optic ModuleDesired Meaning Abnormal Meaning/Action State Observing LEDsNetwork Connection-Related LED States Using Virtual Cable Testing to Diagnose a Cable Troubleshooting Network ConnectionsConfiguration Notes Command SyntaxCable Statistics Displays Viewing the Results of the Cable AnalysisThis Line September Using the Temperature Sensor Managing Temperature SettingsDisplaying the Temperature Chapter Managing the FastIron GS ChassisChanging the Temperature Warning Level Displaying Temperature MessagesRemoving MAC Address Entries Changing the Chassis Temperature Polling IntervalDisplaying Management Module CPU Usage September Power Supply Specifications Chapter Hardware SpecificationsChassis Specifications Physical Dimensions and Weight Chassis SpecificationsEnvironmental Considerations Storage EnvironmentChassis Regulatory Compliance Description Certifications CoolingRegulatory Compliance Mean Time Between Failure Power Source InterruptionsPower Supply Draw Specifications Model Typical Maximum Power Draw SpecificationsSerial Console Port Pinouts Pinouts and Signalling10/100 and Gigabit Port Pinouts Lists the pin assignment and signalling for 10/100/100 portsLC connector 62.5/125 200 For SFP module Power Cords Power Supply SpecificationsWarranty LC connector 1530.33 Up to For XFP module 1561.42 nm 80 kmKey features FGS648 Power Supply Consumption10 Maximum Power Supply Consumption for FGS Models FGS624 Power Supply Input Connector Properties Input Connector and Plug11 Input Connector for Power Supplies 13 Safety Warning Labels on Power Supplies Safety WarningsOutput Specifications Electrical SpecificationsChapter Maintaining the FastIron GS Hardware Hardware Maintenance ScheduleReplacing a Power Supply AC Power Supplies Installation Precautions and WarningsDetermining Which Power Supply Failed Locking screw Removing an AC Power SupplyInstalling an AC Power Supply DC Power Supplies Shows a front view of the DC power supply Removing a DC Power SupplyInstalling a DC Power Supply Ground Removing a 2-port 10-GbE Module Installing or Replacing a 2-port 10-GbE ModuleInstalling a 2-port 10-GbE Module Installing a 2-port 10-GbE Module Installing or Replacing a POE Daughter CardRemoving the Screws for the Top Cover Disassembling the ChassisRemoving the Top Cover Installing a POE Daughter CardPOE Daughter Card POE Daughter Cards Re-assembling the ChassisRemoving a Fiber Optic Module Replacing a Fiber Optic ModuleCabling a Fiber Optic Module Cleaning the Fiber-Optic ConnectorsInstalling a New Fiber Optic Module Status Value Description Digital Optical MonitoringNo optical-monitor alarm interval CLI CommandsSupported Media Show optic port/slotnumberIndustry Canada Statement Appendix a Regulatory StatementsEurope and Australia JapanEnglish Translation of above statement Appendix B Foundry Networks, Inc Page Foundry Networks, Inc Page September Page September