Ricoh 3725e/F530/LF311/3310L operating instructions Immediate Transmission, Set your original

Page 35

Immediate Transmission

Immediate Transmission

Immediate Transmission is conve- nient when:

•You wish to send a document im- mediately as it is scanning.

•You wish to quickly check whether you have successfully connected with the other party's fax machine.

•Your machine's memory is getting full.

The machine dials immediately after you press the {Start} key. The mes- sage is scanned and transmitted page by page without being stored in memory.

Note

❒You can only specify one destina- tion for Immediate Transmission.

❒You can set whether the machine is in Memory Transmission mode or Immediate Transmission mode right after the power is turned on with the User Parameters.

❒The machine does not redial with immediate transmission.

A Check that the Memory Transmis- sion indicator is not lit.

If it is lit, press the {Memory Trans.} key.

B Set your original.

Reference
p.23 “Setting Originals”

C Select any scan settings you re-	2
quire. See p.32 “Scan Settings”.

D Dial.

If you make a mistake, press the {Clear/Stop} key, and then enter the correct number again.

Reference

p.34 “Dialing”

See p.19 “Chain Dial”, Advanced

Features.

E Press the {Start} key.

The machine calls the destination. While it is dialing, the number or name which is programmed as the Own Name or Own Fax Number in the machine of the other party is shown on the display. When con- nected, the machine starts scan- ning the original.

29

Image 35

Contents Basic Features Introduction Table of Contents Registering Troubleshooting Page Page Remarque concernant les utilisateurs au Canada Safety During Operation Safety InformationPage Grounding Important Safety InstructionsImportant Safety Instructions Position of theRCAUTION Label Energy Star Program SpecificationsEnergy Saving Modes Recycled Paper Symbols How to Read this ManualManuals for This Machine Basic Features this manualAdvanced Features Appendix InstallationFront View Guide to ComponentsHandset Option Power SwitchOriginal Tray Original guide Output tray guideControl Panel User Function keys Add Toner indicatorLoad Paper indicator Receive File indicatorNumber keys Status IndicatorsQuick Dial keys Quick Dial Key Flip PlateStarting the Machine Turning On the PowerTurn off the power switch Reading the Display Reading the Display and Using KeysDisplay Prompts Standby DisplayCommunication Display Getting Started Memory Transmission Transmission ModesFaxing Loading Originals Document Feeder Setting OriginalsHow to set A4, B5 JIS Japanese How to set A5 and 81/2⋅ 51/2size originalsOriginal Sizes Difficult to Detect Set the original Make sure that the Memory Trans- mission indicator is litMemory Transmission Press the Start key While the Original is Being Scanned Canceling a Memory TransmissionDuring Transmission Press the OK key Press 0 or 1 to select Yes While the Original is Awaiting TransmissionDisplay the file you want to delete Set your original Check that the Memory Transmis- sion indicator is not litImmediate Transmission Reference Press the Clear/Stop key, and then remove the original Canceling an Immediate TransmissionBefore the Start key is Pressed After the Start key is PressedOriginal Type Scan SettingsResolution ResolutionHalftone Original TypeEntering Numbers Directly DialingMake sure that the machine is in standby display Using Quick DialsPause ToneUsing Speed Dials Using Groups When Specifying a Group with the Group key When Specifying a Group with a Quick DialAuto Receive Selecting the Reception ModeReception Modes Manual ReceiveFaxing Own Fax Number Required by inter- national law Own Name/Fax Header/Own Fax NumberOwn Name Fax HeaderPress 0or 1until 2. Fax Header is displayed RegisteringPress the OK key Enter your Own Name Editing Deleting Own Name/Fax Header/Own Fax Number Quick Dial Press 0 or 1 to select On or Off Enter a fax number with the num- ber keysEnter the destination name Display the number of the Quick Dial key you want to edit Shown and you cannot delete Destination for this key Quick Dial Key Label Dial label Label paper Speed Dial Search letter is registered Press the OK key Press 0 or 1 to select On or Off If you want to edit another Speed Dial number, go to step F Press the User Tools key to re- turn to standby display Assigning the Group Functions to the Group key GroupsPress the User Tools key Press the 0 or 1 to select Add or Exit Editing a Group Name Adding a Fax Number to a Group Press the OK key Press 0 or 1 to select Yes To delete a destination from a group To delete another destination, re- peat steps L to N To delete an entire group To change and delete Quick Dials programmed as groups Keys Entering CharactersAvailable Characters Enter letters, symbols or numbers How to Enter CharactersNot using a wild card Using a wild cardPush the main paper tray in until it stops Loading Paper in the Main Paper TrayAdjusting Volume Adjusting Volume Clearing Original Jams Open the right cover Pull out the jammed paper Clearing a Copy, Fax, or Print JamInside the Machine Open the blue coverMessage Problem/Solution Error MessagesError Messages Cassette, Advanced Features When the Receive File Indicator is LitThis table lists some common problems and their solutions Solving ProblemsSee p.57 Groups Index Deleting Dialing Dial label Editing Registering Error Messages, 74 TTI→Fax Header Memo Memo EN USA H555-8400 REN is separately shown on the label FCC Requirements