JVC XV-NA7SL manual How to set the unit to supply RGB signals

Page 10

Getting started

Getting started

How to set the unit to supply RGB signals

The unit cannot output the RGB signals from the SCART connector and the S-video (Y/C) signals from the S-VIDEO jack simultaneously.

When the unit is turned off

1Set the VIDEO SIGNAL SELECTOR to "COMP./RGB."

Note that you must change the switch position while the unit power is off. Otherwise, the changed setting is not effective.

2Turn the unit to on.

The RGB signal outputs from the SCART connector.

NOTES

•If you connect to a TV with the VIDEO OUT (VIDEO or S-VIDEO) jack, or the SCART connector, make sure that the NTSC/ REMOTE/PAL switch set to "PAL."

•You must change the switch position on the rear panel while unit power is off. Otherwise, the changed setting is not effective.

Connection to a TV equipped with component jacks

You can enjoy high picture quality by connecting the unit’s COMPONENT VIDEO OUT jacks to the COMPONENT VIDEO IN jacks of your TV with the video cables.

Blue

Component video cable (not supplied)

Green Red

The unit

AUDIO OUT

 

DIGITAL OUT

 

 

 

 

 

In this connection, set the NTSC/

 

VIDEO

 

 

 

 

REMOTE/PAL switch to "NTSC" or

 

 

PCM / STREAM

 

VIDEO SIGNAL SELECTOR

 

 

 

 

 

 

 

COMPONENT PAL

 

 

SUBWOOFER

LEFT

COAXIAL OPTICAL

 

COMPONENT

VIDEO

"REMOTE."

 

 

 

 

COMP.

Y/C

REMOTE

/S-VIDEO

 

 

 

 

/RGB

/AV OUT

 

 

 

 

 

 

 

 

 

 

 

 

NTSC

PAL

CENTER

RIGHT

 

 

 

 

AV COMPU LINK

 

 

 

 

 

 

 

 

 

 

 

 

 

REAR

 

 

S-VIDEO

 

 

 

 

 

Blue

Green Red

Red

White

TV

IN

S-VIDEO

Y PB PR

Audio cable (supplied)

White

 

Red

• Connect "Y" to "Y," "PB" to "PB"(CB), "PR" to "PR"(CR) correctly.

VIDEO

COMPONENT IN

LEFT

AUDIO

RIGHT

NOTES

•You must change the switch position on the rear panel while unit power is off. Otherwise, the changed setting is not effective.

•In this connection, make sure that the NTSC/REMOTE/PAL switch set to "NTSC" or "REMOTE."

•When the component video input jacks on the TV is of the BNC type, use an adapter to convert a pin jack to a BNC jack (optional).

•Set [ANALOG OUT] in the [AUDIO] preference display to [2-CH STEREO] (see page 60).

•If your TV has a monaural audio input instead of stereo, you need to use an optional audio cable which converts stereo audio output to monaural.

•To improve audio sound quality, connect the AUDIO OUT jacks to your separate audio equipment (see the following pages).

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents XV-NA7SL If in Doubt Consult a Competent Electrician XV-NA7SLTable of Contents R6PSUM-3/AA15F battery ⋅ Supplied accessoriesAbout this instructions manual Safety precautions Important cautionsNon-playable discs About discsPlayable disc types Audio formatsSVCDs and Video CDs with Playback Control function Disc structureCare and handling of discs To connect to a TV ConnectionsBefore making any connections Connection to a conventional TVTo connect to a TV with the Scart connector Connection to a TV equipped with an S-video jackHow to set the unit to supply RGB signals Connection to a TV equipped with component jacksTo make the Progressive scanning mode selection active To switch the signal format from the remote control unitAbout Scanning Mode Press and hold down the PAL/NTSC buttonPress and hold down VFP Progressive Scan for a few seconds Setting of Still Source type of DVD VideoTo connect to a stereo audio amplifier/receiver ModeAudio cable supplied Red White Amplifier or receiver To connect the power cord To connect to a digital audio devicePrecautions for the safe use of batteries Using the remote control unitTo install batteries in the remote control unit PrecautionsSetting the remote control signal for operating your TV To use the remote control unit for TV operationTo control the volume of a JVC’s amplifier or receiver Manufacturer code listBefore operation Turning on/off the unitUse 5/∞ to select a desired language Initial setup before using the unitUse 5/∞ to select a desired analog output signal type Press EnterUse 5/∞ to select a desired digital output signal type TV screen returns to show the opening displayOPEN/CLOSE Basic playbackInserting and removing discs 1Use 5/∞/2/3 to select a desired item 2Press EnterTo stop playback completely To start playbackPress To stop playback temporarily When the resume mode is set to Disc ResumeResuming playback To memorize the interrupt positionTo resume playback When the resume mode is set to on¶ While stopped, or no disc is inserted To advance or reverse playback rapidly while monitoring Method 1 from the remote control unit onlyVariable speed playback To advance a still picture frame by frameTo playback in slow-motion To locate a desired selection using 4 or ¢To locate the beginning of the scene or song Press 8, then use 1/¡Unit status Disc type What is specified To locate a desired selection using the numeric buttonsUse the numeric buttons to specify the number Press on Screen Other convenient functionsTo check the playback status On Screen AnglePress 5 or ∞ while holding down Angle You can adjust the brightness of the display windowTo change the brightness of the display window Example of the menu bar for DVD VideoPress TOP Menu or Menu Playing from a specific position on a discTo locate a desired scene from the DVD menu TOPUse the numeric buttons to select the desired item To specify a desired title/groupPress 3 or TOP Menu Press TITLE/GROUPUse 2/3 to move to , then press Press on Screen twiceUse the numeric buttons 0 to 10 to enter the desired time ¶ For DVD Video During playback or while Stopped To locate a specific scene from the display DigestPress Digest Up to nine opening scenes are displayedUse page or 5/∞ to select the desired To select a still picture on a DVD Audio discTo play back a bonus group of a DVD Audio disc Use the numeric buttons 0 to 9 to enter the key numberUse 2/3 to move to Prog Changing the playback orderTo playback in a specific order Program play ¶ While stoppedPress 3 to start program playback Use 2/3 to move to Repeat playbackTo playback in random order Random play Press RepeatUse 5/∞ to select A-B Press Subtitle Changing the language, sound and scene angleTo select the subtitle language Subtitle To quit A-B repeat playbackPress Audio fs/Rate To change the audio language or sound AudioUse 5/∞ or Subtitle to select the subtitle Use Audio fs/Rate or 5/∞ to select the desired audioPress Angle To select a scene angle of DVD Video AngleFrom the Angle selection window Use Angle or 5/∞ to select the desired angleTo display continuous still pictures Strobe Special picture playback and picture/sound effectFrom the angle list To zoom in or out pictures Zoom To adjust the picture character VFPUse 2/3 to select the desired preset Use 5/∞/2/3 to move the zoomed positionTo simulate surround sound 3D Phonic Adjust the level of the parameter using 5/∞Select the desired mode by using 2 Press 3D PhonicChecking the sampling frequency and bit rate Press 5/∞ to adjust the effect levelPress and hold down Audio fs/Rate for a few seconds Use 2/3 to select the icon you want to work with Basic operation procedureMenu bar functions Press on Screen againOperation column, we assume Menu bar functions for DVD AudioFollowing table shows the menu bar Associated icon is selectedFunctions available for DVD Video Menu bar functions for DVD VideoTitle Menu bar functions for SVCD/Video CD/Audio CD ALLOperations What is MP3?About MP3 discs Basic operations¶ When the MP3 Control display is shown Move the bar to a desired Group using 5/∞Display using the following procedure You can specify the desired Group/Track fromUse the numeric buttons to specify a desired Group number Direct selectionRepeat playback Use the numeric buttons to specify a desired Track numberChecking the sampling frequency and bit rate Press 7 . Note that the repeat mode remains activeTo stop repeat playback What is JPEG? About Jpeg discsTo see a desired picture Select a desired file using 4/¢Basic operations To display another picture¶ While a Jpeg image is displayed on the TV screen Image may look coarse when a zoomed image is displayedPress Zoom + or To return to a normal screen Press EnterTo see pictures continuously Slide show modePlayback features Selecting the start point of the slide showDirect selection Use the numeric buttons to specify a desired file numberOn the Jpeg Control display goes off TV Screen Selected repeat modeRepeat function JpegSelecting preferences How to set preferencesAbout the Preference display Language menu Table of languages and their abbreviationsPicture menu Digital output signal chart Audio menuRange Compression Auto SPK.SETTING menuDelay ExpertOthers menu This menu allows you to set various system optionsTo set the speaker sizes Making fine tuning for your speakersBass Redirect function To set the delay time To set the speaker levelLimiting playback by children To generate test tone signalsYou can check the level setting by monitoring the test tone Use 5/∞ to select Test Tone and pressUse 5/∞ to move to select Parental Lock and press Enter Enter a 4-digit password using the numeric buttons 0 toTo set Parental Lock for the first time Use 5/∞ to select the country codeAvailable You can change the Parental Lock settings later To change the settingsUse 5/∞ to select the desired option and press Enter Enter your 4-digit password using the numeric buttons 0 to To temporarily release the Parental Lock Parental LockDisplay window Names of parts and controlsFront panel Rear panelRemote control unit Symptom Possible cause Remedy TroubleshootingPower OperationPicture AudioFrequently Asked Questions Question AnswerSpecifications Appendix a Country/Area code list for Parental Lock Appendix B Glossary Ntsc National television system committee PAL Phase Alternation by LineMultisession Packet WritingAbove ALL Let op Vorsicht¡Precaución Huomautus AttenzioneObservera Forsigtig
Top Page Image Contents