Runco DTV-1200 owner manual Stationary Image Warning, Projector Warm UP

Page 18

13FREEZ: press to freeze the projected image.

14TEXT: when adjusting one of the image controls, e.g. contrast, during a meeting, the displayed bar scale

can be removed by pressing 'TEXT' key first. To re-display the bar scale on the screen, press 'TEXT' key again.

15ENTER: to start up the adjustment mode or to confirm an adjustment or selection in the adjustment mode.

16Cursor Keys: to make menu selections when in the adjustment mode.or to increase or decrease the analog level of the image controls when they are first selected.

17EXIT: to leave the adjustment mode or to scroll upwards when in the adjustment mode.

18IR Output LED: lights up when a button on the remote control is pressed. (This is a visual indicator to check the operation of the remote control)

Start Up

Press the Power button on the remote; ensure the main Power button on the rear of the Projector is pressed in.

When this warm up cycle message appears on the screen, the menu offers the possiblity to start with a warm up period (press ENTER) or to skip this cycle (press EXIT). The number of minutes and the horizontal frequecy can be programmed in the 'Service mode' under the item 'Projector Set Up'.

Note: This warm up period is built in so that the Projector can quickly reach its operating temperature.

When starting this warm up period, a full white image is shifted on the CRT faceplate to avoid a burn in. Every 30 seconds a text box will be displayed on another place on the screen with the remaining time to go.

The image dimensions can be adjusted with the cursor keys to avoid scanning on the edges of the CRT's.

PROJECTOR WARM UP

A FULL WHITE PATTERN WILL BE

GENERATED FOR x MIN.

FOR IMMEDIATE USE OF THE

PROJCTOR, PRESS <EXIT>

WARNING : SKIPPING THIS

PROCEDURE CAN REDUCE THE

INITIAL PICTURE QUALITY OF THE

PROJECTED IMAGE;

YOU CAN ADJUST THE IMAGE

DIMENSTIONS WITH THE ARROW

KEYS TO AVOID SCANNING ON THE

EDGES OF THE CRT'S;

THIS OPTION CAN BE DISABLED IN

THE SERVICE MENU

with <ENTER>

<EXIT> to return

To interrupt the warm up period:

1Press EXIT, the warm up menu will be redisplayed with the remaining time indication.

2Press EXIT again to quit the warm up cycle and to display the source.

Start Up in a Specific Source

When the Projector is in Standby, it can be turned ON with a specific source. To do this, simply press the source number button (see page 19).

Stationary Image Warning

!

Do not display a stationary image with full brightness and contrast for longer than 10

minutes, otherwise you risk damage to the CRT's.

16

Page 17 Page 19
Image 18
Page 17 Page 19
Contents DTV-1200 Page Table of Contents Page Page Safety Instructions Safety InstructionsMains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugPage Page Limited Warranty Effective Warranty Date Power Connection to Projector ConnectionsSource Connections Source No Projector Input Remote Button NoRGB Source to Input RGB Source with Composite Sync to Input 4/5Input Select Input RGB Source with Tri-level Sync to Input 4/5 Component Source to Input 4/5RS-232 Connection Remote Control & Local Keypad Getting StartedAudio controls not used Stationary Image Warning Projector Warm UPRemote Commands to the Projector Front of projectorProjector Address Input Selection via the Remote Brightness Control Contrast ControlColor Saturation Control Not used on the DTV-1200 Start UP of the Adjustment Mode Adjustment ModeMain Menu Main MenuColor Adjust Image ControlFormat Select Compose Eye-Q Control Eye-Q Touch UpEye-Q Auto Converge Adjustment Mode Main MenuEntering the Service Menus Service MenusEnter Password Random Access Adjustment Mode Random Access Adjustment ModeRandom Access Selecting Setup Pattern Internal Cross Hatch Pattern VGARandom Access Adjustment Mode Random Access Adjustment Mode Selection MenuPicture Tuning Picture TuningColor Balance Gain adjustment affects the brightest areas of the imagePicture Tuning Color Balance Color BalanceSync Fast/Slow Adjustments Picture TuningColor Balance Peaking Clamp TuningPiture Tuning PeakingRandom Access Adjustment Mode Geometry AdjustmentsHorizontal Phase Adjustments GeometryRaster Shift Adjustments PhaseProjected Raster CRT Faceplate Border Phosphor Left-Right East-West AdjustmentsForbidden Area Coarse ShiftLEFT-RIGHT Start up Left Side CorrectionWhat can be done? Left Side CorrectionTOP-BOTTOM N-S Top-Bottom North-South AdjustmentsGeometry TOP-BOTTOM N-STOP-BOTTOM TOP BOW TOP Keystone Bottom BOW Bottom KeystoneHorizontal Size Adjustments SizeVertical Linearity Adjustments Linearity V SizeLinearity Blanking Vertical Size AdjustmentsBlanking Adjustments BlankingCorrect by pushing the cursor keys up or down Convergence Convergence AdjustmentsConverge Adjustment ConvergenceFocusing FocusingFocusing MidpointTOP BottomLeft Blue on Source Color SelectRight Color SelectRandom Access Installation Service ModeService Mode Service ModeIdentification Projector SetupSoftware version Configuration Text ON/OFFIdentification Run TimeProjector SET-UP RUN TimePassword Change PasswordChange Password Change PasswordProjector SET-UP Projector Address Change Projector AddressChange Baud Rate Baud RateProjector Warm Up Warm Up On/OffProjector Warm UP Warm Up Frequency Projector Warm Up TimeProjector Warm UP Power Up Mode Common AddressCopy a Block Copy ModeMemory Management Memory ManagementDeleting Block by Block Delete ModeDeletion of Blocks Deletion of All BlocksDelete ALL Blocks Set to MidpositionCovergence Mid SET to MidpositionSET to Midposition Undo R & B Convergence MidConvergence MID Green Convergence MIDUndo Green Convergence Mid Focus to MidpositionUndo Focus to Midposition Undo East-West to Midposition North-South Settings to MidpositionEast-West to Midposition To MidpositionUndo Digital Vertical Linearity to Midposition Undo North-South Settings to MidpositionDigital Vertical Linearity to Midposition DIG Vert Linearity MIDAstigmatism to Midposition Digital Horizontal Linearity to MidpositionUndo Digital Horizontal Linearity to Midposition DIG HOR Linearity MIDAll Settings to Midposition Undo All Settings to MidpositionUndo Astigmatism to Midposition Common Settings Common SettingsDynamic Astigmatism Dynamic Astigmatism GreenCRT Run In Cycle Common SettingsGamma Corrections CRT RUN in CycleCRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Menu PositionFlyback Turnover Point I2C Diagnostics 12C DiagnosticsVoltage Diagnostics DecoderProjector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage DiagnosticsPhase Raster Shift Programmable Function KeysProgrammable Function Keys MESSAGES, Warnings and Failures Failure Source Numbers Adjustment Blocks and Source NumbersAdjustment Blocks Memory Blocks Block Header Example of Block HeaderSource input Source number Block header a RS-232 Codes Page CEILING/FLOOR Configuration TD = Throw Distance FactorsSide View DimensionsBottom View Front ViewSpecifications Page RUMA-009450 rev
Top Page Image Contents