Runco DTV-1200 owner manual Sync Fast/Slow Adjustments, Color Balance, Picture Tuning

Page 38

Cut Off Adjustment

1.Push the cursor key or to select 'Custom Red & Blue Cut off' (menu 3).

2.Press ENTER to activate the adjustment.

3.Push the cursor key or to adjust the red cut-off

4. Push the cursor key		or		to adjust the blue cut-off.

5.Press ENTER to return to the Color Balance menu.

6.Push the cursor key or to select 'Custom Green cut off' (menu 4).

7.Press ENTER to activate the adjustment.

8.Push the cursor key or to adjust the green cut-off.

9.Press ENTER to return to the Color Balance menu.

When the color balance is adjusted, press EXIT to return.

COLOR BALANCE

FIXED COLOR BALANCE 3200 4900 6500 9300

CUSTOM RED & BLUE GAIN

CUSTOM GREEN GAIN

CUSTOM RED & BLUE CUT OFF

CUSTOM GREEN CUT OFF

Select with arrow keys

the <ENTER>

Red & Blue:

adjust Red with or

Blue with or <EXIT> to return

menu 1

COLOR BALANCE

FIXED COLOR BALANCE 3200 4900 6500 9300

CUSTOM RED & BLUE GAIN

CUSTOM GREEN GAIN

CUSTOM RED & BLUE CUT OFF

CUSTOM GREEN CUT OFF

Select with arrow keys

the <ENTER>

Red & Blue:

adjust Red with or

Blue with or <EXIT> to return

menu 2

COLOR BALANCE

FIXED COLOR BALANCE 3200 4900 6500 9300

CUSTOM RED & BLUE GAIN

CUSTOM GREEN GAIN

CUSTOM RED & BLUE CUT OFF

CUSTOM GREEN CUT OFF

Select with arrow keys

the <ENTER>

Red & Blue:

adjust Red with or

Blue with or <EXIT> to return

menu 3

COLOR BALANCE

FIXED COLOR BALANCE 3200 4900 6500 9300

CUSTOM RED & BLUE GAIN

CUSTOM GREEN GAIN

CUSTOM RED & BLUE CUT OFF

CUSTOM GREEN CUT OFF

Select with arrow keys

the <ENTER>

Red & Blue:

adjust Red with or

Blue with or <EXIT> to return

menu 4

Sync Fast/Slow Adjustments

What can be done?

The sync function is used to minimize horizontal jittering or tearing at the top to the displayed image. The sync slow/fast function is only available for RGB sources.

How to setup the sync function?

To change the Sync setting, perform the following:

1.Push the cursor keys or to select Sync (menu 1)

2.Press ENTER to toggle between FAST and SLOW.

Note: SYNC is normally used in the SLOW position. The FAST position is used to compensate for unsteady sync pulses from older video playback equipment such as VCRs.

PICTURE TUNING

PICTURE TUNING

COLOR BALANCE

SYNC: FAST

PEAKING

CLAMP TUNING: normal

Select with or
then <ENTER>
<EXIT> to return	menu 1

36

Image 38

Contents DTV-1200 Page Table of Contents Page Page Safety Instructions Safety InstructionsMains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plugPage Page Limited Warranty Effective Warranty Date Power Connection to Projector ConnectionsSource Connections Source No Projector Input Remote Button NoInput Select Input RGB Source to InputRGB Source with Composite Sync to Input 4/5 RS-232 Connection RGB Source with Tri-level Sync to Input 4/5Component Source to Input 4/5 Remote Control & Local Keypad Getting StartedAudio controls not used Stationary Image Warning Projector Warm UPRemote Commands to the Projector Front of projectorProjector Address Input Selection via the Remote Color Saturation Control Not used on the DTV-1200 Brightness ControlContrast Control Start UP of the Adjustment Mode Adjustment ModeMain Menu Main MenuColor Adjust Image ControlFormat Select Compose Eye-Q Control Eye-Q Touch UpEye-Q Auto Converge Adjustment Mode Main MenuEntering the Service Menus Service MenusEnter Password Random Access Random Access Adjustment ModeRandom Access Adjustment Mode Selecting Setup Pattern Internal Cross Hatch Pattern VGARandom Access Adjustment Mode Random Access Adjustment Mode Selection MenuPicture Tuning Picture TuningColor Balance Gain adjustment affects the brightest areas of the imagePicture Tuning Color Balance Color BalanceColor Balance Sync Fast/Slow AdjustmentsPicture Tuning Peaking Clamp TuningPiture Tuning PeakingRandom Access Adjustment Mode Geometry AdjustmentsHorizontal Phase Adjustments GeometryRaster Shift Adjustments PhaseProjected Raster CRT Faceplate Border Phosphor Left-Right East-West AdjustmentsForbidden Area Coarse ShiftLEFT-RIGHT Start up Left Side CorrectionWhat can be done? Left Side CorrectionTOP-BOTTOM N-S Top-Bottom North-South AdjustmentsGeometry TOP-BOTTOM N-STOP-BOTTOM TOP BOW TOP Keystone Bottom BOW Bottom KeystoneHorizontal Size Adjustments SizeLinearity Vertical Linearity AdjustmentsLinearity V Size Blanking Vertical Size AdjustmentsBlanking Adjustments BlankingCorrect by pushing the cursor keys up or down Convergence Convergence AdjustmentsConverge Adjustment ConvergenceFocusing FocusingFocusing MidpointLeft TOPBottom Blue on Source Color SelectRight Color SelectRandom Access Installation Service ModeService Mode Service ModeIdentification Projector SetupSoftware version Configuration Text ON/OFFIdentification Run TimeProjector SET-UP RUN TimePassword Change PasswordChange Password Change PasswordProjector SET-UP Projector Address Change Projector AddressChange Baud Rate Baud RateProjector Warm UP Projector Warm UpWarm Up On/Off Projector Warm UP Warm Up FrequencyProjector Warm Up Time Power Up Mode Common AddressCopy a Block Copy ModeMemory Management Memory ManagementDeleting Block by Block Delete ModeDeletion of Blocks Deletion of All BlocksDelete ALL Blocks Set to MidpositionCovergence Mid SET to MidpositionSET to Midposition Undo R & B Convergence MidConvergence MID Green Convergence MIDUndo Focus to Midposition Undo Green Convergence MidFocus to Midposition Undo East-West to Midposition North-South Settings to MidpositionEast-West to Midposition To MidpositionUndo Digital Vertical Linearity to Midposition Undo North-South Settings to MidpositionDigital Vertical Linearity to Midposition DIG Vert Linearity MIDAstigmatism to Midposition Digital Horizontal Linearity to MidpositionUndo Digital Horizontal Linearity to Midposition DIG HOR Linearity MIDUndo Astigmatism to Midposition All Settings to MidpositionUndo All Settings to Midposition Dynamic Astigmatism Common SettingsCommon Settings Dynamic Astigmatism GreenCRT Run In Cycle Common SettingsGamma Corrections CRT RUN in CycleCRT Drive Mode CRT Drive ModeCRT Drive Mode Memory Banks Flyback Turnover Point Flyback Turnover PointMenu Position I2C Diagnostics 12C DiagnosticsVoltage Diagnostics DecoderProjector Diagnostics Projector DiagnosticsProjector Diagnostics Voltage DiagnosticsProgrammable Function Keys Phase Raster ShiftProgrammable Function Keys MESSAGES, Warnings and Failures Failure Source Numbers Adjustment Blocks and Source NumbersAdjustment Blocks Memory Blocks Block Header Example of Block HeaderSource input Source number Block header a RS-232 Codes Page CEILING/FLOOR Configuration TD = Throw Distance FactorsSide View DimensionsBottom View Front ViewSpecifications Page RUMA-009450 rev